skilsaw SPT67WMB - User Manual

Questions and Answers

M
michaelwhiteJul 29, 2025
Why won't my skilsaw Saw start?
- B
  Barbara RichardsonJul 29, 2025
  Several factors can prevent your skilsaw Saw from starting. First, check if the power cord is securely plugged in. If it is, inspect the fuse or circuit breaker of the power source, and replace the fuse or reset the breaker if necessary. Examine the power cord for any signs of damage, and if damaged, have it replaced by an Authorized Bosch Service Center or Service Station. A burned-out switch or a faulty trigger can also be the cause; in such cases, have the switch replaced by a qualified service technician.
J
Joshua MedinaAug 4, 2025
What to do if my skilsaw SPT67WMB cut binds, burns, stalls motor when ripping?
- J
  Jessica HudsonAug 4, 2025
  If your skilsaw Saw experiences binding, burning, or motor stalling during ripping, the following could be the cause. A dull blade with an improper tooth set can cause these issues, so try discarding the blade and using a different one. If you are working with a warped board, ensure the concave or hollow side faces down and feed slowly. Blade binding can also cause this, so assemble the blade and tighten the Vari-Torque clutch.
R
Robert RoweAug 10, 2025
Why is my skilsaw Saw blade not coming up to speed?
- C
  Cynthia WhiteAug 10, 2025
  If the blade on your skilsaw Saw isn't reaching full speed, it could be due to an inadequate extension cord—either too light or too long. Replace it with a suitable cord. Another potential cause is low house voltage; if this is the case, contact your electric company.
C
Christine AcostaAug 16, 2025
Why is my skilsaw SPT67WMB Saw blade slipping?
- L
  Latasha VasquezAug 16, 2025
  If the blade is slipping, assemble the blade and tighten the Vari-Torque clutch.
D
daniel17Aug 22, 2025
What to do if skilsaw SPT67WMB Saw has excessive vibration?
- B
  Brittany ArnoldAug 22, 2025
  Excessive vibration in your skilsaw Saw can be attributed to a blade that is out of balance. If this is the case, discard the blade and use a different one.

Summary

Safety Symbols

General Power Tool Safety Warnings

Safety Rules for Circular Saws

Kickback Causes and Related Warnings

Understand kickback causes and learn precautions to avoid sudden, uncontrolled reactions of the saw.

Lower Guard Function

Check and ensure the lower guard operates freely and closes instantly to prevent injury.

Additional Safety Warnings

Functional Description and Specifications

Assembly

Attaching the Blade

Step-by-step instructions for securely attaching the blade to the saw, including the Vari-Torque Clutch.

Vari-Torque Clutch

Explanation of the Vari-Torque Clutch that helps reduce kickback by allowing the blade to slip.

Operating Instructions

Depth Adjustment

Instructions on how to adjust the cutting depth for various lumber sizes and to minimize splintering.

Bevel Adjustment

Guidance on adjusting the saw's bevel angle up to 45° and beyond using the adjustment lever and stop.

Switch Operation

Electric Brake

General Cuts

Plunge Cuts

Rip Cuts

Compound Miter Cuts

Maintenance

Service

Cleaning

Troubleshooting

Saw Will Not Start

Identifies common reasons why the saw won't start and provides remedies for power cord, fuse, switch, or trigger issues.

Blade Does Not Come Up to Speed

Cut Binds, Burns, Stalls Motor When Ripping

Lists reasons for cutting issues like dull blades, warped boards, or binding, and suggests solutions including clutch adjustment.

Blade Slipping

Addresses blade slipping issues that prevent cutting, recommending Vari-Torque clutch adjustment for resolution.

skilsaw SPT67WMB Specifications

General

Motor	15 Amp
Blade Diameter	7-1/4 inches
Arbor Size	5/8 inches
No Load Speed	5, 300 RPM
Worm Drive	Yes
Type	Circular Saw
Max Cutting Depth at 90 degrees	2-7/16 inches
Cord Length	8 ft