Skyjack SJM 3015 User Manual

Models 3015, 3219, 3220, 3226, 4620, 4626,
4830, 6826 And 6832
SJM & SJll
Series
For Service please call ....................................................................... 800 275-9522
Skyjack Inc. Service Center, 3451 Swenson Ave., St. Charles, IL. 60174 FAX 630 262-0006
For Parts in North America and Asia please call ......................................
800 965-4626
Skyjack Inc. Parts Center, 3451 Swenson Ave., St. Charles, IL. 60174 .......... FAX 888 782-4825
For Parts & Service in Europe please call .....................................................
31 297 255 526
Skyjack Europe Communicatieweg 29, 3641 SG Mijdrecht Netherlands ......... FAX 31 297 256 948
129916AB-A Printed in Canada August 2007
OPERATING MANUAL
This manual MUST be kept and stored with the aerial platform at all times.

Skyjack SJM 3015 Specifications

General

Platform Height	15 ft
Overall Width	30 in
Drive Type	Electric
Max Working Height	21 ft
Gradeability	25%
Power Source	Battery
Battery Voltage	24V
Stowed Height	6.5 ft
Drive Speed	2.0 mph

Summary

Section 1 - About Your Aerial Platform

1-2. Warranty Statement

Details the manufacturer's warranty terms for parts and workmanship.

1-3. Major Components

1-6. Operator's Control Box

1-8. Lifting Mechanism

1-9. Maintenance Support/Safety Bar

Describes the safety bar used to support the platform during maintenance.

1-11. Lowering Warning System (If Equipped)

1-12. Tilt Sensing System (If Equipped)

1-16. Operator Safety Reminders

Provides essential safety advice and precautions for platform operators.

1-17. Electrocution Hazard

Details risks and safe approach distances from energized power lines.

1-18. Safety Precautions

Outlines critical safety rules to prevent accidents during operation.

Section 2 - Operation

2-2. Operator Qualifications

Specifies the requirements for trained and authorized personnel to operate the platform.

2-3. Operator's Responsibility for Maintenance

2-4. Maintenance And Inspection Schedule

Outlines the recommended intervals for platform maintenance and inspections.

2-5. Owner's Inspections

2-7. Maintenance Support/Safety Bar

Provides instructions for the proper use of the maintenance support safety bar.

2-9. Tilt Alarm (If Equipped)

2-10. Base Controls

2-10-a. Emergency Main Power Disconnect Switch

Details the location and function of the emergency power shut-off switch.

2-10-b. Base Controls

2-10-c. Base Control Box (If Equipped)

2-12. Operator's Control Box: 2 Speed and Optional 3 Speed

Details the controls on the platform operator's box for 2 or 3 speed models.

2-13. Operator's Control Box: Proportional Controller

Describes the controls for platforms equipped with a proportional controller.

2-14. Powered Extension Deck Control Box (If Equipped)

2-17-a. Emergency Lowering System (Machines with Holding Valves)

Procedure for lowering the platform during an emergency with holding valves.

2-17-b. Hydraulic (Machines with Velocity Fuses)

Procedure for lowering platform using hydraulic systems with velocity fuses.

2-18. Set-Up Procedure

Step-by-step instructions for setting up the aerial platform before first use.

2-19. Raise The Platform

Detailed steps for safely raising the aerial platform to the desired height.

2-20. Lowering Warning System (If Equipped)

2-21. Pre-start Inspection

Procedure for performing a visual inspection before operating the platform.

2-22. Operators Checklist

2-23. Setting the Base Controls

2-24. Shutdown Procedure

2-25 Emergency Lowering Procedure

Detailed procedure for safely lowering the platform in an emergency.

2-26. Winching And Towing Procedures

2-28. Stabilizers (Model 3226 only)

2-29. Battery Service Procedures

2-30. Battery Charging Procedures

2-31-a. Battery Charger (If Equipped)

2-31-b. Battery Charger (If Equipped)

2-31-c. Battery Charger (If Equipped)

Section 2 - Tables

Table 2-1a. Specifications and Features

Table 2-1b. Specifications and Features

Table 2-2. Floor Loading Pressure

Table 2-4. Maximum Platform Capacities (Evenly Distributed)

Table 2-5. Maintenance and Inspection Schedule

Outlines the recommended maintenance and inspection tasks and frequencies.