SkyLink HA-300 - User Manual

The sensors must be programmed to the Household Alert
®
Long Range
Receiver before they can communication. You may program the sensors
to one of the 4 zones. Follow the instructions below:
1. Plug in an AC adapter to the receiver.
2. The green LED will be on indicating it is turned on.
3. Open the back cover and there is a learn button. Press and hold this
learn button for 5 seconds, until both green LED a
nd zone 1 red LED
You may now release the learn button.
4. If you would like to program the sensor to zone 1, activate the
sensor while the zone 1 red LED is
Press the SET button
on the back of the sensor to activate it.
5. If you would like to program the sensor to other zones, press the
learn button again, until the red LED
at the zone you want to
program the sensor to, then activate the sensor.
6. Once the sensor is programmed, the green LED will be steadily on
and none of the red zone LEDs will be on.
Note: Each zone can program up to 4 sensors. If you try to program a
sensor into a zone, the programmed sensor will be erased.
You cannot erase a
sensor. You must erase all sensors from
the receiver, then program the ones you would like to keep. To erase
all the sensors from the receiver:
1. Remove the adapter from the receiver.
2. Open the back cover, press and hold the learn button. Do not
release the learn button until step 4.
3. While holding onto the learn button, plug in the adapter to the receiver.
4. You may release the learn button wh
en the LEDs on the receiver are on.
5. You have erased all sensors from the receiver.
1. INTRODUCTION
Deluxe Motion Monitoring Kit
Model HA-300
The Deluxe Motion Monitoring Kit is designed to monitor movement around
your house. The motion sensor can be placed either indoor or outdoor. Once
In this package, you should
two Indoor/Outdoor Motion Sensors, a
Household Alert
®
Long Range Receiver, an adapter, two ball-head joint
and screws.
Please follow the instructions below to setup your motion sensors and
the receiver.
Adapter
4 pcs 3 x 18 screws
(Included)
2 x Indoor/Outdoor
Motion Sensor
2x Ball-head joint
Plug in the adapter to the receiver
Insert 9V alkaline battery (option) to the sensor
2. PROGRAMMING
3. INSTALLATION
A ball-head joint is necessary to mount the sensor at a desire location.
A height of 7 ft is recommended, depending on your application. Once a
location is selected, mount the ball-head joint to this location by screws
provided. Once the ball-head joint is mounted to the wall, slide the back
of the sensor into the ball-head joint. The mounting angle can be
adjusted. Please refer to “Walk Test” to determine the best mounting
angle.
After mounting the sensor at the desired location, it is
important to perform a walk test in order to determine
if the sensor is detecting the things you want to detect.
In order to control how far the sensor can “see”, this can be done by
adjusting the angle of the sensor. To reduce the detection range, simply
move the sensor downward. To increase the range, move the sensor
up to around 12 degrees. This will give the maximum range. However,
this may not be desired if the sensor is placed outdoors, since a false
trigger may occur if the sensor is set to detect motion in a distance.
You should walk in the area that you would like the sensor to monitor.
Place the slide switch on the side of the receiver to “Alert” position. The
receiver will beep if the sensor detects your movement. If the receiver
does not respond, adjust the mounting angle accordingly. After motion is
detected once, the sensor will not be triggered unless no motion is
detected for 20 seconds. Therefore, wait for at least 20 seconds during
walk testing between 2 activations.
Perform walk test in the undesired area to ensure movement cannot be
detected.
Household Alert
®
Long Range Receiver
SET Button
7 ft
Tips: The sensor should not face towards direct sunlight, placing near
heat or cold producing devices (i.e. A/C or furnance vents, fans, ovens,
heaters etc.) that may cause false triggers.
Move the sensor downward to
reduce the range.
Move the sensor up to around
12 º to give maximum range.
The sensitivity of the motion sensor is adjustable. Change the setting by
placing the connector on either the ”High” (connector position “1”) or
“Low” (connector position “2”) position. When the sensitivity is set to
“Low”, more movement is required to trigger the sensor. It is recom-
mended to set the sensitivity to “Low” and perform a “Walk Test”. If the
walk test result is the sensitivity does not require to be
adjusted further. If the walk test
result shows the sensitivity is too
low, then you can change the
sensitivity setting to “High”. Please
perform the walk test after changing
the sensitivity setting.
1 - High 2 - Low
Learn Button
Page 1 of 2
Erasing a sensor
MOUNTING
WALK TEST
SENSOR SENSITIVITY

Summary

Deluxe Motion Detection Kit Introduction

Kit Contents

Lists the components included in the Deluxe Motion Detection Kit, such as the receiver, motion sensor, batteries, and mounting hardware.

Programming the Motion Sensor

Pairing Sensor with Receiver

Step-by-step instructions for programming the motion sensor to the receiver using the Learn button and LED indicators.

Erasing a Sensor

Instructions on how to remove a previously programmed sensor from the receiver's memory.

Installing the Motion Detector

Mounting the Motion Detector

Guidance on selecting the optimal location and height for mounting the motion sensor for effective detection.

Walk Test Procedure

Instructions on performing a walk test to verify the motion sensor's detection range and functionality.

Operating the Motion Detector

Selecting Operating Modes

Instructions on how to select between Alert, Alarm, and Off modes using the receiver's slide switch.

Alert Mode Functionality

Describes the receiver's beep and LED flash response when a sensor is activated in Alert mode.

Mute and Alarm Modes

Details on using the mute button and the siren activation in Alarm mode for sensor alerts.

Off Mode Behavior

Explains that in Off mode, only the zone LED will flash upon sensor activation, with no audio output.

Loss of Signal Indication

Troubleshooting Loss of Signal

Explains the rapid flashing LED for lost signals and provides steps to resolve connection or battery issues.

FCC Compliance Information

FCC Rules and Warnings

Details compliance with FCC Part 15, including conditions for operation and warnings against unauthorized modifications.

Product Warranty and Support

Warranty Terms

Outlines the one-year warranty for defects, including repair or replacement policies and proof of purchase requirements.

Customer Service Contact

Provides contact details for FAQs, email, phone, and fax support for product inquiries and assistance.

SkyLink HA-300 Specifications

General

Brand	SkyLink
Model	HA-300
Category	Security System
Language	English