Smeg BCC01 User Manual

EN - 7
EN
Use
Dispensing can be stopped at any
time by pressing the dispensing
key again .
Remember to reassemble the tray
(14) at the end of any dispensing.
It is completely normal that after a
prolonged inactivity of the machine
(breaks longer than 20 min ) the
rst coffees are not at the right
temperature . The tips to obtain a hot
coffee immediately are given in the
section “What to do if ...”
Customization of the quantity
It is possible to customize, for each type of dispensing,
the quantity of coffee or water dispensed .
• Place a cup or large cup under the
dispenser.
• Press for at least 3 seconds one of the
keys relative to the drink to be dispensed.
The selected key lights up ashing; the
machine emits a double sound to signal
the modication of the preset program.
• On reaching the desired quantity, stop
dispensing by pressing the key again; an
acoustic signal indicates the memorization
of the quantity.
Any customization of the drinks
remains saved for future dispensing.
To restore the manufacturer’s settings,
press the keys (9) and (20)
simultaneously for at least
3 seconds.
The machine emits a single sound to
signal the restoration of the factory
settings.
Turning off the machine
• Check that the drip tray (14) is positioned
correctly.
• If there is no water, the machine remains in
the rinse position until the tank is lled.
• Press the button (9) , the keys (16), (17),
(18), (19) light up ashing in sequence and
the machine, if it has dispensed at least one
coffee, performs a self-cleaning cycle.
At the end of the self-cleaning cycle, the
machine switches off.
MACHINE SETTINGS
(Fig. C-G)
Through a programming menu it is possible
to set the water hardness and the acoustic
signals.
Activation / deactivation of acoustic
signals.
The acoustic signals can be disabled /
enabled by keeping the keys (17) and
(20) pressed for three seconds; the key
(17) ashes three times indicating the
memorization of the setting.
Setting the water hardness.
The machine is factory set to “Hard Water
Level”. The machine can also be set according
to the actual water hardness in the various
regions for less frequent descaling.
If you don’t know the water hardness, use
the supplied test strip (33) and follow the
instructions below.
• Remove the supplied reactive strip from its
packaging.
• Fully submerge the strip in a glass of water
for about one second.
• Remove the strip from the water and slightly
shake it. Read the results after about one

Smeg BCC01 Specifications

General

Product type	Espresso machine
Built-in grinder	Yes
Capacity in cups	1 cups
Grinder capacity	150 g
Coffee input type	Coffee beans, Ground coffee
Coffee maker type	Fully-auto
Country of origin	China
Appliance placement	Countertop
Water tank capacity	1.4 L
Maximum operating pressure	19 bar
Reservoir for brewed coffee	Cup
AC input voltage	220–240 V
AC input frequency	50 - 60 Hz
Auto power off after (max)	20 min
Package depth	265 mm
Package width	495 mm
Package height	445 mm
Package weight	7000 g
Quantity per pack	1 pc(s)
Cappuccino making	No
Control type	Buttons
Product color	Red
Housing material	Aluminium, Plastic
Pallet weight	168000 g
Quantity per pallet	24 pc(s)
Pallet GTIN (EAN/UPC)	8017709301002
Quantity per pallet layer	6 pc(s)
Number of layers per pallet	4 pc(s)
Pallet net width	800 mm
Pallet net height	1900 mm
Pallet net length	1200 mm
Pallet net weight	120000 g

Weight and Dimensions

Depth	433 mm
Width	180 mm
Height	336 mm
Weight	5000 g