Other
functions
"
••
1
III.IIBI'"
"I.
,
x:
l
~
~
l
~
Adjusting
the
sound
charalcteristics - BAUFAD/SUB
You
can adjust the balance, fader, and subwoofer
volume.
1
Press
the
select
button
repeatedly
untUi
"BAL,"
"FAD"
or
"SUB"
appears.
The item changes as follows:
LO\f\I*1
---+
MID*1
---+
HI*1
---+
BAL (left-right)
--+
FAD (front-rear)
---+
SUB
(subwoofer volume)*2
---+
AUX*3
*1
VVhen
EQ3 is activated (page
9).
*2
VVhen
the audio output is
set
to "SUB" (page 9).
"ATT" is displayed
at
the lowest setting,
and
can
be adjusted up
to
21 steps.
*3
VVhen
AUX
source is activated (page
10).
2
Rotate
the
volume
control
dial
to
adjust
the
selected
item.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
Custc)mizing
the
equalizer
curve
-EQ3
"CUSTOM"
of
EQ3 allows you to make your
own equalizer settings.
1
Select
a sourc4e,
then
press
(
EQ3)
repeatedly
to
select
"CUSTOM."
2
Press
the
select
button
repeatedly
until
"LOW," "MID"
or
"HI"
appears.
3
Rotate
the
volume
control
dial
to
adjust
the
selected
item.
The volume level is adjustable in 1 dB steps,
fronl
-10
dB
to +10 dB.
Example:
CDX··GT320/GT32W
Repeat steps 2 and 3 to adjust the equalizer
curve.
To
restore the factory-set equalizer curve,
press and hold the select button before the
setting is complete.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
Tip
Other equalizer types are also adjustable.
1
Press
and
hold
the
select
button.
The setup display appears.
2
Press
the
select
button
repeatedly
until
the
desired
item
appears.
3
Rotate
the
volume
control
dial
to
select
the
setting
(example
"ON"
or
"OFF").
4
Press
and
hold
the
select
button.
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and
setting.
The following items can be set (follow the page
reference for details):
"e"
indicates the default settings.
CLOCK-ADJ
(Clock Adjust) (page 5)
BEEP
•
To
set "BEEP-ON" (e) or "BEEP-OFF."
AUX-A*1 (AUX Audio)
To
turn the AUX source display "AUX-A-ON"
(e)
or "AUX-A-OFF" (page 10).
A.OFF
(Auto Off)
To
shut off automatically after a desired time
when the unit is turned off,
- "A.OFF-NO"
(e),
"A.OFF-30S (Seconds),"
"A.OFF-30M (Minutes)" or "A.OFF-60M
(Minutes)."
SUB/REAR*1
To
switch the audio output.
- "SUB-OUT"
(e):
to output to a subwoofer.
- "REAR-OUT": to output to a power amplifier.
DEMO (Demonstration)
To
set "DEMO-ON"
(e)
or "DEMO-OFF."
DIM
(Dimmer)
To
change the brightness
of
the display.
- "DIM-ON": to dim the display.
- "DIM-OFF"
(e):
to deactivate the dimmer.
M.DSPL
(Motion Display)
To
select the Motion Display mode.
CDX-GT320/GT32W
- "M.DSPL-SA"
(e):
to show moving patterns
and spectrum analyzer.
- "M.DSPL-OFF": to deactivate the Motion
Display.
CDX-G
T220/G
T22W
/G
T120/G
T12W
- "M.DSPL-ON" (e): to show moving patterns.
- "M.DSPL-OFF": to deactivate Motion
Display.
continue
to
next
page---+
9
To Next Page
Loading...
