Sony CPD-E200 User Manual

SPECIFICATIONS
D99C
CHASSIS
SERVICE MANUAL
CPD-E200
CPD-E200
US Model
Canadian Model
Chassis No. SCC-L31A-A
TRINITRON
®
COLOR MONITOR
MICROFILM
Picture tube
Video image area
Resolution
Standard image area
Input signal
Video
Sync
0.244-0.250 mm aperture grill pitch
17 inches measured diagonally
90-degree deflection
(16" maximum viewing image)
Approx. 328 X 242 mm (w/h)
(14
1/4
x 9
5//8
inches)
Horizontal: Max. 1600 dots
Vertical: Max. 1200 lines
Approx. 312 x 234 mm (w/h)
(12
1/4
x 9
1/4
inches)
Analog RGB (75 ohms typical)
0.7 Vp-p,
± 5%, Positive
Separate HD/VD,
TTL Polarity Free
External Composite,
TTL Polarity Free (2K ohms impedance)
Deflection frequency
AC input voltage / current
Dimensions
Mass
Plug and Play
Horizontal: 30 to 85 KHz
Vertical: 48 to 120 Hz
100 to 120 V, 50/60 Hz, 1.7A
220 to 240V, 50/60Hz, 0.9A
404 x 414 x 420mm (w/h/d)
(15
15/16
x 16
3/8
x 16
1/2
inches)
Approx. 18.8 kg (41 lb 7 oz.)
DDC/DDC2B, DDC2Bi, GTF
Design and specifications are subject to change without notice.

Sony CPD-E200 Specifications

General

Screen Size	17 inches
Viewable Image Size	16.0 inches
Maximum Resolution	1600 x 1200
Recommended Resolution	1280 x 1024
Dot Pitch	0.24 mm
Input Video Signal	Analog RGB
Horizontal Refresh Rate	30-70 kHz
Vertical Refresh Rate	50 - 160 Hz
Input Connectors	15-pin D-sub
Power Consumption	85 W
Refresh Rate	85 Hz @ 1280 x 1024

Summary

SPECIFICATIONS

Picture Tube and Image Specifications

Resolution and Image Area

POWER MANAGEMENT

Power Saving Modes Explained

Describes monitor power saving modes compliant with VESA DPMS standard.

SELF DIAGNOSIS FUNCTION

Failure Status and LED Indicators

TIMING SPECIFICATION

Horizontal, Vertical, and Sync Timing Data

SAFETY CHECK-OUT PROCEDURES

Leakage Test and Component Warnings

Outlines safety checks for AC leakage and critical component warnings.

Setup and Initial Configuration

Connecting Monitor to Computer

Customizing Monitor Display Settings

Navigating the On-Screen Menu System

Adjusting Brightness, Contrast, and Centering

Covers adjustments for brightness, contrast, and picture centering.

Helpful Hints and Information (HELP)

HELP Menu Guidance for Common Issues

Resetting Adjustments and Power Saving

Troubleshooting Common Issues

Screen Lines and On-Screen Messages

Explains thin lines and troubleshooting messages like 'OUT OF SCAN RANGE'.

Trouble Symptoms and Remedies

Resolving No Picture and Image Alignment Issues

Guides on fixing no picture, flickering, ghosting, centering, and fuzzy images.

Addressing Color and Button Operation Problems

Solutions for color issues, button operation, hum sounds, and monitor information display.

Self-Diagnosis and Specifications

Self-Diagnosis Function Operation

Detailed Monitor Specifications

SECTION 2 DISASSEMBLY PROCEDURES

Cabinet, Service Position, and Board Removal

Steps for removing the cabinet, placing in service position, and removing boards.

2-4. PICTURE TUBE REMOVAL

Anode Cap Removal and Handling Precautions

SECTION 3 SAFETY RELATED ADJUSTMENTS

HV ADJ Checks and Procedures

Performing checks on HV regulator, protector, beam protector, and B+ voltage circuits.

SECTION 4 ADJUSTMENTS

Landing and Convergence Rough Adjustments

Procedures for rough adjustments of landing, convergence, and geometry.

Fine Adjustments for Landing and Convergence

Detailed steps for fine-tuning landing and convergence using specific tools.

4-7. Digital Convergence Adjustment

Digital Convergence Adjustment Modes

Instructions for adjusting digital convergence in low and high modes.

Convergence Specification Standards

SECTION 6 EXPLODED VIEWS

Chassis Exploded View and Parts