Sony DVS-2000C - Page 27

ie aoe il
Section 1 OPERATION
1-20
BiB BOMURE
Section 1 OPERATION
© TERMINAL (2 — 3 +11) 38F (D-SUB 9)
At yF~—- OPE PIR RRETT I CR ESICISRY
WH
bh
SATS
ERI
pu
—
SPIEL
ET.
RS-232CfS SUS ICMLL TID. AA Fe -AMBOIeY
TERMINALS (CPU-1562507_L) & AISI BEL ET.
@ MATRIX(? bh U 7 z)HF(D-SUB 9)
RS-422A(2 SAS IC BL ed Ya 7 2 - ARSC
+. HWBT bY DD RAL yF He -EBRLEN. FUR
WINFLT 2 be LA, IGEDMEMTOR,
65—-BE= COMTI LET. HHRIRIKIL. WED Oo
BKDS-20724 Mt MAIL DEMS OFT.
@ omer 2-7 F157 +7 b)RF(D-SUB OE)
FVINGNFLI 2 b SLT. AUK IZ Se
Say bU—ILEYD, DMELink EHS ROO VY
H—F x — A FAST (RS-422A18 SAG ERD CT.
@® GPi(ARAWA) se (D-SUB 25E>)
SES EL. bUA-ABSOAMHASFOETF. AN
BRK. HHS E THD, THOU TARY
SAEOTP ISS ABABECT,
@® EDITOR(T 71 S—)A. BaEF(D-SUB 9E>)
LHPEFAYVIPIAY hU-NY AF SBVE200KE EH
UT, HBS AL Fx -EBY bU-NFSEOOA
YS—7 = — ART (RS422A8 SRI CF.
ISEDITOR AST EH LET. EDITOR BHT ILGRO
VAFAUPRATCT.
@ PANELU ‘S28 F(D-SUB 9)
ay
bh
uU—-IASRILBKDS-2010%
F
HBL
T.
Atv
Fy
—ERMETSEOOA
VS
—-7
x
—
AT
(RS422A
BSB
CT.
© ~ACINACHHAD TF BE>)
100~240VOACHIRIKBRLET. BRI Pid. HAT
Shhist CH SCO SRSA T SEDECHH
RFE
@ 4 (7 -AyeF
YAF ADR ERLET.
Mis Mom Be
‘Section? OPERATION
© TERMINAL connector (D-sub 9-pin)
Connect a control terminal for use in maintenance and
initial switcher settings, or when using the ISR support.
This connector complies with the RS-232C standard, and
has the same function as that of the switcher’s 9-pin
internal TERMINAL connector (on the CPU-156 board).
@ MATRIX connector (D-sub 9-pin) ~
This is an interface connector which allows you to
connect an external matrix switcher, or to connect a
second digital multi effects unit after connecting the first
digital multi effects unit to the DME connector ®. The
optional BKDS-2072 board must be installed to use this
connector. This connector complies with the RS-422A
standard.
@ DME (digital mutti-effects) connector
(D-sub 9-pin)
This is an interface connector which allows you to .
connect a digital multi-effects unit, to control the AUX
bus or use the DME-Link® function. This connector
complies with the RS-422A standard.
@® GP (general purpose /O) connector
(D-sub 25-pin)
Connect to external equipment to input and output trigger
signals. There are 8 input lines and 8 output lines.
Conditions for input and output can be programmed.
@® EDITOR A, B connectors (D-sub 9-pin)
This is an interface connector complying with the RS-
422A standard which allows you to connect an editing
control system such as the BVE-2000 to control the
switcher externally. Normally use the EDITOR A
connector. The EDITOR B connector is provided for
future expansion.
-@® PANEL connector (D-sub 9-pin)
Connect a control panel such as the BKDS-2010 to
operate the switcher from the control panel. This connec-
tor complies with the RS-422A standard.
® AC IN connector (3-pin)
Connect to 100 to 240 V AC power. Select an appropriate
power cord according to the safety rule in your area.
@® Groundterminal
Connect the system ground.