Sony SLV-E700 User Manual

Lists all supported Sony VCR models covered by the manual.

Details technical parameters such as channel coverage, output signals, and power consumption.

Procedure for checking safety after service or repairs to ensure proper functioning.

Warning about components identified by a mark, critical for safety.

Procedures for removing the drum assembly and replacing the upper drum.

Outlines periodic checks and replacements for maintenance.

Instructions for cleaning the rotating head assembly and tape movement system.

Guide to cleaning the VCR's drive system components.

Instructions for unpacking the VCR and setting up the remote commander.

Guide on how to connect the VCR to a TV and other devices.

Steps to tune the TV to the VCR for playback.

Step-by-step guide for setting up the VCR using the EASY SET UP function.

Instructions for setting up VIDEO PLUS manually for recording broadcasts.

Guide on how to play back a video tape using the VCR.

Steps for recording TV programmes onto a tape using the VCR.

Instructions for recording stereo and bilingual broadcasts.

Guide for setting up timer recordings for TV programmes.

Instructions for timer recording using PDC signals.

How to adjust tape tracking for optimal picture quality during playback.

Guide to using the Optimum Picture Control feature for recording.

Procedures for removing the upper case and front panel assembly of the VCR.

Steps for removing the control switch block and MF-254 board.

Instructions for removing the HI-6 board and the bottom plate.

Procedures for removing the PS-328 and CP-67 boards.

Instructions for removing HF-34, PV-12, and RV-37 boards.

Procedures for removing the MA-215 board and MD block assembly.

A general block diagram showing the main functional units of the VCR.

Block diagram for the servo and system control functions.

Block diagram for timer, tuner, and mode control systems.

Schematic diagrams of the VCR's frame and major components.

Schematic diagram for the RV-37 board (Video Process, HiFi, Audio, Head Amp).

Schematic diagram for the MA-215 board (Servo/System Control).

Schematic diagram for the HI-6 board (Timer/Tuner/Mode Control).

Schematic diagram for the MF-254 board (LED Control).

Exploded diagrams of the case and front panel assemblies with part numbers.

Lists of capacitors, connectors, and diodes for the CP-67 board.

Lists of transistors and resistors for the CP-67 board.

Lists of components for the DC-58 and HF-34 boards.

Lists of capacitors and diodes for the HF-34 board.

List of components for the HI-6 board.

Lists of switches and vibrator components for the MA-215 board.

List of components for the MF-254 board.

List of components for the PS-328 board.

List of components for the PV-12 board.

Lists of capacitors and transistors for the RV-37 board.

List of miscellaneous parts including switch blocks and wire.

List of hardware items such as screws and washers.

Pin function table for the MA215 board's video block interface.

Pin function table for audio system control.

Pin function table for RF modulator and input selection.

Procedures for mechanical adjustments of VCR components.

List of instruments required for performing electrical adjustments.

Guide on connecting equipment for electrical adjustments.

Procedures for checking input signal and using alignment tapes.

Procedure for checking specified input-output levels.

Procedures for checking power supply voltages on the PS-328 board.

Procedures for adjusting the servo system functions.

Adjustment procedures for system control and timer settings.

Procedures for adjusting the VCR's video system.

Procedure for checking the Y FM carrier frequency.

Procedure for checking white and dark clip levels.

Procedure for checking the playback Y level.

Procedure for adjusting the SECAM detection.

Adjustment procedure for VCO frequency on the HF-34 board.

Procedure for checking deviation on the HF-34 board.

Adjustment procedure for the band pass filter on the HF-34 board.

Adjustment procedure for AF switching position on the MA-215 board.

Procedure for adjusting the ACE head.

Procedure for adjusting recording bias on the MA-215 board.

Procedures for checking overall noise levels.