2
STR-DA3000ES
Items Display Remark
Protector on/off SPECIAL XXX: ON or OFF (switching with
[--/+] dial)
PROTECTOR ON/OFF
[
XXX
]
Model version display SPECIAL ####: model
####
****
vX.XX @@@@
****
: destination
X.XX: main microprocessor software version
@@@@: Sum value of flash memory in the main microprocessor
Model/distination change SPECIAL ####: model,
****
: destination, XX: at or fx
MODEL [
####
****
]
XX (switching with [--/+] dial)
FL display fonts test SPECIAL
**
: 20 to 1F, X: character (switching with [--/+] dial)
FL FONT 0x
**
=
[
X
]
FL display test ALL ON Each time
[DISPLAY] button to change as follows.
all on t test pattern 1 t test pattern 2 t all off t all on
Audio swap SPECIAL Switching with
[--/+] dial
SWAP
[
XXXXXXXXXXX
]
DSP reset SPECIAL XXX: ON or OFF (switching with
[--/+] dial)
DSP RESET
[
XXX
] Note: Since it continues being reset when “DSP RESET [ON]”
is chosen, be sure to return to “DSP RESET [OFF]”
DSP 1 IRAM DSP 1 IRAM The umbers which can be changed will blinks
I
[
*****
]
=
XXXX To select the digit: Press the [TUNING +] or [TUNING --] button
To select the number when the umbers (
*****
or XXXX) blinks:
Rotate the [--/+] dial
To perform the write when the umbers (XXXX) blinks:
Press the
[MEMORY/ENTER] button
*****
: instruction RAM address
XXXX: instruction RAM address data
Note: When parenthesis is the position of instruction RAM
address data, up/down of the menu item by
the [MENU] dial
are invalid
DSP 1 ARAM DSP 1 ARAM The umbers which can be changed will blinks
D
[
*****
]
=
XXXXXXXX To select the digit: Press the [TUNING +] or [TUNING --] button
To select the number when the umbers (
*****
or XXXXXXXX)
blinks: Rotate the [--/+] dial
To perform the write when the umbers (XXXXXXXX) blinks:
Press the [MEMORY/ENTER] button
*****
: coefficient RAM address
XXXXXXXX: coefficient RAM address data
Note: When parenthesis is the position of
coefficient
RAM
address data, up/down of the menu item by
the [MENU] dial
are invalid
DSP 2 IRAM DSP 2 IRAM The umbers which can be changed will blinks
I
[
*****
]
=
XXXX To select the digit: Press the [TUNING +] or [TUNING --] button
To select the number when the umbers (
*****
or XXXX) blinks:
Rotate the [--/+] dial
To perform the write when the umbers (XXXX) blinks:
Press the [MEMORY/ENTER] button
*****
: instruction RAM address
XXXX: instruction RAM address data
Note: When parenthesis is the position of instruction RAM
address data, up/down of the menu item by
the [MENU] dial
are invalid
SPECIAL MENU MODE
Procedure:
1. Press the I/1 button to turn on the main power, then while pressing the [MEMORY/ENTER] button, press the [MOVIE] button in order.
2. The message “MENU EXPANDED !” appears.
3. Each time the [MENU] dial is turned clockwise, the item is switched in order as follows.
4. To release from this mode, while pressing the [MEMORY/ENTER] button, press the [MOVIE] button in order again.
5. The message “MENU EXPAND OFF” appears.
To Next Page
Loading...
