Sony TC-252 D - Tape Handling and Editing

REC VOL
+ Téte d'enregistrement /écoute
© © Kombi-Kopf
[L}iR) {Lj IR]
Invert and reverse the tape reels.
Renverser et éechanger les bobines.
Umstellen und vertauschen die Spulen.
Microphone (low impedance)
Microphone (basse impédance)
Mikrophon (niedriger Impedanz)
Ome Telephone pickup TP-4S
CS Pick-up telephonique TP-4S
Telephontonabnehmer TP-4S
3
|
SONY
Radio
equipped
with
a
recording
jack
!
SONY
Radio
avec
une
prise
d'enregistrement
'
SONY
Radio
mit
einer
Tonbandbuchse
es
RK-69
Tape
recorder
©
Magnétophone
§
or)
Tonbandgerat
©
©
to
monitor
outputs
[AUX
IN}
aux
sorties
de
relais
|
an Mithorausgange
RK-50
Sound-on-aound
recording
LINE
OUT]
L]
Enregistrement
son-sur-son
Multiplay-aufmahme
Stereo headphone DR-5A
Casque d’écoute stéréo
DR-5A
Stereokopfhorer DR-5A
Microphone mixer MX-600M
Melangeur de microphone
MX-600M
Mikrophon Mischpult MX-600M
Microphone (low impedance)
Microphone (basse impédance)
Mikrophon (niedriger impedanz)
Stereo
recording/Enregistrement
en
stéréo/Aufnehmen
im
Stereoverfahren
1
|
REC/PB
head
=—
4. Select the desired tape speed.
5. Set the figures on the Tape Counter to [000] by pressing
the Tape Counter Reset Button.
6.
Press
until
locked
the
Record
Lever
[L],
and
adjust
the
record
level
by
turning
the
Record
Level
Control
[L].
Deflection
of
the
needles
of
the
Level
Meter
to
the
boundary
of
the
red
and
black
zones
provides
normal
recording
level.
7.
While
holding
the
Record
Lever
[L]
down,
turn
the
Function
Selector
to
[»]
position.
The
recording
of
track-1
will
start.
8. When track-1 is completed, invert and reverse the reels.
Track-4 recording will then be continued,
9.
To
record
on
the
track-3
and
track-2,
connect
the
program
source
to
the
Auxiliary
Input
Jack
[R]
or
the
Microphone
Jack
[R].
Adjust the record level by locking the right Record Lever
and turning the Record Level Control [R]. Then, repeat
the procedure of the track-1 and track-4 recording
SOUND-ON-SOUND RECORDING
Sound-on-Sound Recording is possible with the use of the SONY
Monophonic Microphone Mixer MX-600M or SONY Stereo Micro-
Phone Mixer MX-eS. Connect the microphone mixer to the
recorder
using
the
SONY
Connecting
Cord
RK-80
(optionat
accessory) as illustrated.
1. Record basic source materia! on track-1 of the left channel
according to monophonic recording on the previous para-
graphs. When the recording is finished, rewind the tape to
tne beginning.
2. Plug in a low impedance stereo headphone to the Headphone
Jack. Listening through the headphone, make another
recording on track-3 of the right channel. From the left
headphone, the playback of left channel is heard, and from
the right headphone, the composite recording being made
is heard.
yx While recording, be careful not to turn the Record Level
Control of the recorder or of the Microphone Mixer fully
clockwise.
3. When the end of the tape is reached, rewind it and play back
track-3; the composite recording will then be played back.
ERASING TAPE
The erase head operates in record mode, therefore, every time
you make a recording, any previous recording on the tape is
automatically erased. You can also erase a tape without adding
a new recording as follows.
1. Place the recorded tape which you want to erase on the
Feed Reel Spindle.
2. Turn the Record Level Controls fully counterfockwise and
disconnect any input source.
3. While holding both Record Levers down, turn the Function
Selector to [>] positisn. While the tape s in motion,
track-1 and track-3 will be erased. Tape sped of 7% ips
is recommended.
4. When erasing of track-1 and track-3 is completed, invert and
reverse the reels. Track-4 and track-2 will the n be erased.
By pressing only the Record Lever [L], track-1 will be erased
and track-4 will be also erased when the reels are #nverted and
reversed. By pressing only the Record Lever [R', track-3 will
be erased and track-2 will be also erased whenthe reels are
inverted and reversed.
For fast erasure, use a bulk eraser.