Sony Trinitron KV-27V20 - Operating Video Equipment

VCR manufacturer code numbers
Manufacturer
Code number
Sonv 301,302,303
Aiwa
338
Admiral (M. Wards) 327
Audio Dynamic 314, 337
Bell & Howell (M. Wards)
330,343
Broksonic
319,317
Canon
309, 308
Citizen
332
Craig
315,302,332
Curtis Mathis
304, 338, 309
Daewoo
341,312, 309
DBX
314, 336, 337
Dimensia
304
Emerson 319, 320, 316, 317, 318, 341
Fisher
330. 334,335, 333
Funai 338
General Electric
329, 304, 309
Go Video
322
Goldstar
332
Hitachi
306, 304, 305
Instant Replay 309,308
|C Pennev
309, 305, 304, 330, 314, 336, 337
INC 314, 336,337
Kenwood
314, 336, 332, 337
LXI (Sears)
332, 305, 333, 334, 330, 335, 338
Magnavox
308, 309,310
Marantz
314, 336, 337
Marta
332
Memo rex 309,335
Minolta
305, 304
Mitsubishi /MCA
323, 324, 325, 326
Multi tech
325, 338, 321
NEC
314, 336, 337
Olympic 309,308
Optimus 327
Panasonic
308, 309, 306, 307
Pen tax 305, 304
Philco
308, 309
Philips
Pioneer
308, 309, 310
308
Quasar
308, 309, 306
RCA/PROSCAN
304, 305,308, 309, 311, 312, 313, 310
Realistic
309, 330, 328,335, 324, 338
Sansui
314
Singer
315
Samsung
- 322*, 313, 321
San vo
330, 335
Scott
312, 313, 321,335, 323, 324, 325, 326
Sharp
327, 328
Shin tom
315
Signature 2000 (M. Wards)
338, 327
Svl vania
308,309, 338, 310
Symphonic
338
Tashiro
332
Tatung
314,336,337
Teac 314, 336, 338, 337
Technics 309, 308
Toshiba
312,311
Wards
327, 328. 335, 331, 332
XR-1000
315
Yamaha
330,314,336, 337
Zenith
331
MDP manufacturer code numbers
Manufacturer
Code number
MDP
Sonv
701
Kenwood
707
Magna vox 70,3
Maranz
702
Mitsubishi
702
Panasonic
704
Philips
703
Pioneer
702
RCA
702
Sanyo
706
Sharp
7l)5
Yamaha
703
Notes
• ll more than one code number is listed, try entering them one by one, until you come to
the correct code for vour equipment.
• In some rare cases, you may not be able to operate your non-Sony video equipment with
the supplied remote commander. This is because vour equipment may use a code that is
not included with this remote commander. In this case, please use the equipment's own
remote control unit.
• The code numbers lor Sonv equipment are assigned at the factory as follows:
\ HS VCR 301 (preset code for the supplied remote
commander)
8 mm VCR 302
Beta, ED Beta VCRs 303
• Whenever you remove the batteries — to replace them, for example — if too much time is
taken, the code numbers may revert to the factory settings and must be reset.
Operating video equipment
VTR (FUNCTION)
Video operating
buttons
rr
t
O®o o
-g3 CD CD
O © © ©
© © ©
CD CD CD CD
© ® ©
© © ©
© © ®
"o]©!©^
VTR (POWER)
0-9 buttons
ENTER
CH +/-
Use the video operating buttons on the remote
commander to operate the video equipment. Press VTR
(FUNCTION) before operating the video equipment.
Operating a VCR
Buttons on the remote commander
Tt> turn on or off
Press VTR (POWER),
To select a channel
directly
Press the 0-9 buttons.
To change channels
Press CH +/-.
To record
Press ► while pressing •. First release
► , then release •.
To plav
Press ► .
To stop
Press ■ .
To fast forward
Press
To rewind the tape Press
To pause
Press II.
To resume normal playback, press again.
To search the picture
forward or backward
Press ►► or during playback.
To resume normal playback, release the
button.
To change input mode
Press TV/VTR.
Operating an MDP
Buttons on the remote commander
To turn on or off
Press VTR (POWER).
To play
Press
To stop
Press ■
To pause
Press II. To resume normal playback,
press again.
To search the picture
lorward or backward
Keep pressing ►► or during
playback. To resume normal playback,
release the button.
To search the chapter
torward and backward
Press CH + /-.
Note
• It tin 1 vidro equipment does not have a certain function, the corresponding button on this
remote commander will not operate.
28
Operations