How to fix Sony TV with good picture but no sound?
If your Sony TV displays a good picture but has no sound, first, try increasing the volume level. If that doesn't work, make sure the TV is not muted by pressing the mute button.
Why does my Sony TRINITRON KV-SZ29M80 have good picture but noisy sound?
If your Sony TV has a good picture but noisy sound, access the “Channel Setup” menu and select the appropriate “TV System” from “Manual Program”.
Why does my Sony TRINITRON KV-SZ29M80 TV have a snowy picture and noisy sound?
A snowy picture and noisy sound on your Sony TV can often be resolved by checking the antenna cable and its connections at the TV, VCR, and wall. You may also need to check the antenna setup. Additionally, try to preset the channel again using the “Manual Program” option in the “Channel Setup” menu, or set the “Signal Booster” to “Auto” from “Manual Program”. If the issue persists, consider using an external booster.
What to do if my Sony TV has distorted picture and noisy sound?
If your Sony TV shows a distorted picture and noisy sound, try turning off or disconnecting any external booster you might be using. Also, access the “Channel Setup” menu and set the “Signal Booster” to “Off” from “Manual Program”.
What causes double images or “ghosts” on Sony TV?
Double images or “ghosts” on your Sony TV can be due to antenna issues. Try using a highly directional antenna or fine-tuning the channels using the “Fine” function. Also, check the antenna setup. If you're using an external booster, try turning it off or disconnecting it.
Why is there no color on my Sony TV?
If your Sony TV has no color, first, go to the “Picture” menu, select “Custom” from “Picture Mode”, and adjust the “Color” level from “Picture Adjustment”. If that doesn't work, check the “Color System” setting in the “Setup” menu and ensure it is set to “Auto” (usually). It may also be an antenna issue.
What causes dotted lines or stripes on Sony TRINITRON KV-SZ29M80 TV screen?
Dotted lines or stripes on your Sony TV screen can be caused by interference from nearby equipment. Avoid using a hair dryer or other similar equipment near the TV. Also, check the antenna setup.
What causes abnormal color patches on Sony TRINITRON KV-SZ29M80 TV?
Abnormal color patches on your Sony TV screen can be caused by interference from nearby electronic devices. Keep external speakers or other electrical equipment away from the TV.
What does it mean if the standby indicator on my Sony TV flashes red?
Count the number of times the standby indicator flashes red on your Sony TV. Then, turn off the TV using the main power button and contact your nearest Sony service center.
How to fix picture slant on Sony TRINITRON KV-SZ29M80?
To correct a slanted picture on your Sony TV, go to the “Picture Position” under the “Setup” menu. From there, adjust the “Picture Rotation” and “Picture V-Position” settings until the picture is aligned correctly on the screen.
Interpreting STANDBY indicator flashes for fault diagnosis.
Explains the blinking pattern of the standby indicator.
Location of the standby indicator on the TV's front panel.
Displaying diagnostic results on the TV screen.
Procedures for displaying and clearing self-diagnostic results.
Schematic of the self-diagnostic circuit and its components.
Steps to remove the rear cover from the TV.
Instructions for removing the speaker assembly.
Procedure for removing the main chassis assembly.
Details on placing the TV in a service position.
Steps to remove the H1 board.
Procedure for removing the A board.
Instructions for safely removing the picture tube.
Adjusting beam landing for optimal picture alignment.
Correcting color convergence for red, green, and blue dots.
Procedure for adjusting the focus of the picture.
Adjusting the G2 (screen) voltage for proper brightness.
Calibrating white balance for accurate color reproduction.
Performing service adjustments using the remote commander.
General method for performing adjustments via service mode.
Detailed adjustments for picture quality parameters.
Adjusting geometric distortion for correct picture shape.
Overall block diagram of the TV's system architecture.
Diagram showing the physical location of circuit boards.
Key for understanding schematic diagram symbols and notations.
Lists voltages and waveforms at various test points.
Layout diagrams of the printed circuit board traces.
Identification and diagrams of common semiconductor components.
Exploded view of the main TV components and their assembly.
List of all capacitors used in the circuit with their specifications.
List of all connectors with their pin assignments and types.
List of diodes with part numbers and descriptions.
List of integrated circuits used in the TV with part numbers.
List of transistors used in the circuit with their part numbers.
List of resistors with part numbers and specifications.
To Next Page
General