EasyManua.ls Logo

Sony UTX-M40 - User Manual

Sony UTX-M40
56 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
UHF Wireless Microphone Package
UHF Synthesized Transmitter
UHF Synthesized Wireless Microphone
UHF Synthesized Diversity Tuner
Operating Instructions
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
UWP-D21/D22/D26/D27
UTX-B40
UTX-M40
UTX-P40
URX-P40
URX-P41D
5-042-114-11 (1)
© 2022 Sony Corporation

Table of Contents

Questions and Answers

  • S
    Sabrina MartinNov 24, 2025
    Why is there sound interruption or noise with my Sony UTX-M40?
    • D
      Duane PittsNov 24, 2025
      To resolve sound interruption or noise with your Sony Microphone system, ensure that the channel setting is the same on both the transmitter and tuner. Avoid using the same channel for two or more transmitters. If using multiple transmitters, configure them to different channels within the same channel group to prevent signal interference. Use channels separated by at least two channels (250 kHz). Also, adjust the output level on the tuner and the reference input level on the camcorder. Move the transmitter and tuner further apart, and turn off any unused tuners. If you are using a camcorder, be aware that beeping noises, crackling or squealing sounds, or hum noise can occur due to interference from the camcorder's media access, Wi-Fi, or LCD backlight. Adjust the output level and referenc...
  • R
    robinhernandezAug 23, 2025
    How to fix no sound on Sony Microphone system?
    • T
      tracie31Aug 23, 2025
      If your Sony Microphone system isn't producing any sound, make sure the channel setting on the transmitter matches the tuner. Confirm the transmitter is on and reduce the distance between it and the tuner if the transmission output is weak. Ensure the transmitter is set to microphone input, not line level. The compander mode setting on both devices should be the same. Also, check if the transmitter is muted and change the MUTE SETTING if it is set to PTT HOLD.
  • S
    Shannon ClineAug 26, 2025
    How to fix a Sony UTX-M40 that does not turn on?
    • W
      waltonmichaelAug 27, 2025
      If your Sony Microphone system is not turning on, ensure the batteries are inserted with the correct polarity. Replace low batteries with new ones. Clean any dirt from the battery terminals and the battery compartment with a cotton swab. If using battery power, make sure batteries are inserted and the power source is set to 'BATT ONLY'. If using the SMAD-P5, check that it is correctly connected to the camera or tuner and that the power supplies for the tuner and camera are correctly linked.
  • J
    John ChanAug 27, 2025
    What to do if there is no sound from my Sony Microphone system?
    • J
      Jason HopkinsAug 28, 2025
      If there is no sound from your Sony Microphone system, verify that the channel setting is the same on both the transmitter and tuner. Confirm that the transmitter is on and reduce the distance between the transmitter and tuner. Ensure the transmitter is set to microphone input, not line level. The compander mode setting must be the same on both devices. Check if the transmitter is muted and release it by pressing the POWER/MUTE button. Review the MUTE SETTING menu and audio output connector settings. If using the SMAD-P5, ensure the Analog/Digital switch is correctly set. For microphones connected to the MIC INPUT, configure the microphone setting in the MIC SELECT menu to match the microphone type.
  • S
    stephaniethomasAug 29, 2025
    Why is the noise louder when connected with SMAD-P5 on my Sony UTX-M40?
    • G
      georgedavidAug 29, 2025
      To resolve the issue of louder noise when connected with SMAD-P5 compared to the XLR-BMP conversion output cable on your Sony Microphone system, adjust the reference input level and reference recording level of the camcorder, or adjust the OUTPUT LEVEL on the tuner to set the appropriate audio level.
  • R
    Ruth HallSep 18, 2025
    How do I fix the attenuator settings on my Sony UTX-M40 Microphone system?
    • G
      Gregory MoodySep 18, 2025
      If the attenuator cannot be set on your Sony Microphone system, the GAIN MODE menu may be set to AUTO GAIN, or the INPUT LEVEL menu may be set to LINE. Change the GAIN MODE menu and INPUT LEVEL menu settings.
  • H
    heather74Sep 15, 2025
    How to troubleshoot the infrared transmission on a Sony Microphone system?
    • M
      Michelle Jackson MDSep 16, 2025
      If the transmitter channel on your Sony Microphone system cannot be set with infrared transmission, reduce the distance between the infrared receptor on the transmitter and the infrared transmission port on the tuner to within about 20 cm (8 in.). Also, minimize interference from infrared communications or direct sunlight by placing the transmitter and tuner as close as possible. Ensure that the SYNC MODE menu setting is set to IR.
  • T
    tammy55Sep 17, 2025
    How to troubleshoot NFC communication on a Sony UTX-M40 Microphone system?
    • P
      Pamela GreenSep 17, 2025
      If the transmitter channel of your Sony Microphone system cannot be set via NFC communication, ensure the N-Marks of both units are facing each other and are approximately 5 mm apart, with no metallic objects nearby. Also, verify that the SYNC MODE menu setting is NFC.
  • M
    Michael FullerSep 7, 2025
    Why transmitter channel cannot be set via NFC communication on Sony Microphone system?
    • A
      Annette RogersSep 8, 2025
      If you are unable to set the transmitter channel on your Sony Microphone system via NFC communication, place the N-Marks approximately 5 mm from each other, ensuring they are facing each other and that there are no metallic or other objects nearby.
  • E
    erichodgesSep 5, 2025
    What to do if Sony Microphone system does not turn off?
    • F
      frobertsonSep 5, 2025
      If your Sony Microphone system does not turn off, release the locked status in the POWER LOCK menu. Alternatively, if the unit is set so that power cannot be turned on/ off using the POWER/MUTE button, set the POWER/MUTE menu to POWER/MUTE, or turn the unit off using the POWER button.

Summary

Product Features Overview

Power Supply Management

Transmitter Power Supply

Details power supply methods for UTX-B40 and UTX-P40 transmitters.

Hand-held Microphone Power

Details power supply methods for the UTX-M40 hand-held microphone.

Tuner Power Options

Details power supply options for URX-P40/P41D tuners.

Basic Operation Procedures

Transmitter and Tuner Power On

Steps to power on the transmitter and portable diversity tuner.

NFC SYNC Channel Setup

Procedure for setting channels using NFC SYNC.

Tuner Configuration Menus

Menu Structure and Operation

Setting the Receive Channel

Clear Channel Scan Procedure

Active Channel Scan Procedure

Adjusting Monitor Audio Level

Transmitter Configuration Options

Selecting Group;Channel (GP;CH)

Setting Audio Output Level

NFC Sync Transmitter Settings (SYNC RX->TX)

NFC Sync Tuner Settings (SYNC TX->RX)

Selecting Preferred Power Supply (POWER SOURCE)

Setting Compander Mode (COMPANDER)

Transmitter Menu Structure and Operation

Simple Mode Transmitter Settings

Setting the Transmit Channel

Adjusting Audio Input Attenuation (ATTENUATOR)

Setting Audio Gain (GAIN MODE)

Switching Audio Input Level (INPUT LEVEL)

Audio Muting Function Operation (MUTE SETTING)

System Configuration Examples

Troubleshooting Error Messages

Common Error Messages and Solutions

Lists common error messages and their solutions.

General Troubleshooting Guide

Unit Not Turning On Issues

Addresses problems with the unit not powering on.

No Sound or Weak Sound Issues

Solves issues related to no sound or weak sound output.

Sound Interruption and Noise Issues

Solves problems with sound interruption or noise.

NFC Communication Channel Setting Issues

Solves problems setting channels via NFC communication.

Important Usage and Safety Notes

Usage Restrictions and Precautions

Notes on frequency band use, NFC function, and general operation.

Medical Device Interference Warning

Warning about interference with medical devices.

Usage and Storage Environment

Preventing Electromagnetic Interference

Technical Specifications

Transmitter (UTX-B40;M40;P40) Specifications

Detailed specifications for transmitters.

Body-pack Transmitter (UTX-B40) Specifications

Detailed specifications for the UTX-B40 body-pack transmitter.

Hand-held Microphone (UTX-M40) Specifications

Detailed specifications for the UTX-M40 hand-held microphone.

Plug-on Transmitter (UTX-P40) Specifications

Detailed specifications for the UTX-P40 plug-on transmitter.

Tuner (URX-P40;P41 D) Common Specifications

Common specifications for URX-P40 and URX-P41D tuners.

Portable Diversity Tuner (URX-P41 D) Specifications

Detailed specifications for the URX-P41D portable diversity tuner.

Sony UTX-M40 Specifications

General IconGeneral
BrandSony
ModelUTX-M40
CategoryMicrophone system
LanguageEnglish

Related product manuals