Sony VPL-VW760ES Service Manual

2-1 (E)
VPL-VW760ES
Section 2
Electrical Adjustments
2-1. Notes on Servicing
. The laser light of this unit is very intense. To prevent unnecessary irradiation on the eyes, care must be
taken with the following points in performing the repair under the irradiation of the laser light. Be sure
to follow the contents in this manual when performing the repair.
- The laser light has characteristics that the energy goes straight without diffusing, which is different
from the sunlight and illumination light. In case that eyes are intensively irradiated with the straight
energy, there is a risk of causing damage to the retina, etc.
- The laser light from the lens and the light leaked from inside of this unit are the same level as the
existing lamp light. However, when performing the repair, avoid directly viewing the laser light
except for the lens.
. The laser diode is used as a light source of this unit.
Never allow the light source to emit light with the cabinet removed.
Otherwise, it may cause damage to eyes or skin.
. Do not remove the lens when the set is lighting.
Otherwise, it may cause damage to eyes or skin.
. In order to avoid inappropriate use of the laser diode, do not disassemble the laser source unit.
. Never allow the light source to emit light with the cover of this unit removed except during the mainte-
nance.
When allowing the light source to emit light with the cover of this unit removed during maintenance, be
sure to perform the light dimming adjustment before removing the cover of this unit. Otherwise, it may
cause damage to eyes. (Refer to “Light dimming adjustment” in Section 1-6.)
. The Class2 laser light is emitted from the light source when opening the cover and pressing the limit
switch.
The laser light may cause damage to eyes or skin. Therefore, be careful not to view the laser beam
directly.
2-2. Preparations
Perform the adjustments at least 20 minutes after turning on the power.
2-2-1. Required Equipment
. Personal computer (PC)
OS: Windows 7 or later
t
. PC is used for copying the adjustment data from the supplied CD-ROM to the USB memory in “2-3-1.
When Replacing the Optical Block Assembly” .
. PC is not used in “2-3-4. When Replacing the QE Board”.
. HDMI cable (for PC connection)
t
The HDMI cable is used for the adjustment in Section 2-3-4.
. VG (Programmable video signal generator)
. Chrominance difference gauge (CL500 or equivalent)

Sony VPL-VW760ES Specifications

General

Matrix size	0.74 \
Native aspect ratio	-
Projection distance	- m
Vertical scan range	48 - 92 Hz
Horizontal scan range	19 - 72 kHz
Projection technology	SXRD
Screen size compatibility	60 - 300 \
Projector native resolution	DCI 4K (4096x2160)
Focus	Auto
Zoom capability	Yes
Focal length range	- mm
Vertical lens shift range	-80 - 85 %
Horizontal lens shift range	-31 - 31 %
Supported video modes	480p, 576p, 720p, 1080p, 2160p
Supported graphics resolutions	1920 x 1080 (HD 1080), 3840 x 2160, 4096 x 2160
Noise level	24 dB
On Screen Display (OSD) languages	ARA, CHI (SIMPL), CHI (TR), DEU, DUT, ENG, ESP, FRE, ITA, JPN, KOR, NOR, POL, POR, RUS, SWE, THA, TUR
DVI port	No
HDMI connector type	Full-size
Serial interface type	RS-232C
USB 2.0 ports quantity	1
VGA (D-Sub) ports quantity	0
Ethernet LAN data rates	10, 100 Mbit/s
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	5 - 35 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	35 - 85 %
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.4 W
Power consumption (typical)	430 W
Power consumption (network standby)	1 W
Light source type	Laser
Service life of light source	- h
Placement	Desktop
Product type	Standard throw projector
Product color	Black
Market positioning	Home cinema

Weight and Dimensions

Depth	496 mm
Width	560 mm
Height	223 mm
Weight	20000 g