Speed Queen SF3JM - User Manual

Questions and Answers

D
David NavarroAug 17, 2025
Why won't my Speed Queen Washer start?
- J
  James WyattAug 17, 2025
  If your Speed Queen Washer won't start, ensure the power cord is fully plugged into the electrical outlet. Check the laundry room fuse or circuit breaker. Verify that the controls are properly set and press the START keypad. Also, ensure the loading door is closed tightly. If it is a coin operated machine, insert coin(s) or card. Finally, make sure the door latch is properly adjusted relative to the door lock.
R
Ryan BellAug 20, 2025
What to do if my Speed Queen SF3JM Washer won’t fill?
- J
  Jacob WolfeAug 20, 2025
  If your Speed Queen Washer won't fill, make sure the power cord is fully plugged into the electrical outlet and check the laundry room fuse or circuit breaker. Ensure the controls are properly set and press the START keypad. Verify the loading door is closed tightly and the hot and cold water faucets are turned on. Check that the fill hoses are not kinked or twisted. Additionally, clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses.
R
Ryan HernandezAug 23, 2025
What to do if my Speed Queen SF3JM won’t drain?
- J
  Jerry DeanAug 23, 2025
  If your Speed Queen Washer won't drain, ensure the drain hose is not kinked or twisted and that it is not clogged. Also, make sure the drain receptacle is not clogged. A foreign object trap in the pump may be clogged, so clean the trap. Refer to Maintenance section.
M
Michelle McconnellAug 26, 2025
Why is my Speed Queen SF3JM vibrating or moving slightly?
- B
  Bryce HarrisAug 26, 2025
  If your Speed Queen Washer is vibrating or moving slightly, make sure the washer is level, as uneven leveling can cause vibration. Also, ensure the washer is installed on a solid, sturdy, and level floor and that rubber feet are installed on all four leveling legs.
T
Terri BarronAug 28, 2025
How to fix water leaks in Speed Queen Washer?
- A
  Audrey LoweryAug 28, 2025
  To address water leaks in your Speed Queen Washer, check that the fill hoses are properly installed on the faucets and the washer’s water mixing valve. Inspect the condition of the fill hoses, replacing them every five years. Ensure the drain receptacle is not clogged and check the laundry room plumbing. Examine the rubber door gasket for tears or holes. If the laundry load may be oversudsing, make sure you are using low-sudsing, high efficiency (HE) detergent. If the laundry load may be overloaded, make sure you are using proper load sizes. Also, make sure the outside perimeter of the door glass where the seal contacts the glass is clean.
T
Timothy CaseAug 30, 2025
Why is my Speed Queen SF3JM so noisy?
- W
  William HeathAug 30, 2025
  If your Speed Queen Washer is noisy, make sure the washer is level, as uneven leveling can cause vibration. Also, some sounds may be a part of normal operation for a frontload washer.
B
brian36Sep 2, 2025
Why is my Speed Queen SF3JM not spinning or tumbling?
- J
  jenniferpettySep 2, 2025
  If your Speed Queen Washer won't spin or tumble, make sure the power cord is plugged all the way into the electrical outlet and check the laundry room fuse or circuit breaker. Ensure the controls are properly set and press the START keypad. Verify that the loading door is closed tightly. If the drive belt is broken, call the service person. A foreign object trap in the pump may be clogged, clean the trap. Refer to Maintenance section.
T
Thomas WardSep 5, 2025
Why is my Speed Queen Washer stopping or pausing during the cycle?
- C
  Connie ChaseSep 5, 2025
  Pauses are part of the Speed Queen Washer’s normal operation. Check the laundry room fuse or circuit breaker. The wash load may be unbalanced; the washer will stop and then restart spin automatically.
K
Kimberly BowenSep 8, 2025
Why is my Speed Queen Washer load too wet?
- J
  Jasmine RobertsSep 8, 2025
  If your Speed Queen Washer leaves the load too wet, it may be due to an unbalanced wash load; redistribute the load. Alternatively, the load might be too small, so add items to make it a full load.
J
jaredalexanderSep 12, 2025
Why does my Speed Queen Washer have too many soap suds?
- T
  Theresa MaldonadoSep 12, 2025
  If your Speed Queen Washer has too many soap suds, it may be because the laundry load may be oversudsing. Make sure you are using low-sudsing, high efficiency (HE) detergent and the amount of detergent recommended on the detergent’s label. Also, make sure you are using proper load sizes, as the laundry load may be overloaded.

Summary

Safety Information

Important Safety Instructions

Provides crucial safety precautions for using the washer to prevent injury or damage.

Installation

Order of Installation Steps

Lists the sequential steps for correctly installing the washing machine.

Remove Shipping Materials

Connect Fill Hoses

Details on connecting the water inlet hoses to the washer and supply.

Water Supply Requirements

Specifies the necessary water pressure, temperature, and connection types.

Connecting Hoses

Install Washer Electrical Cord

Guidance on connecting the power cord, including voltage and amperage.

Non-Gravity Drain Models - Connect Drain Hose to Drain Receptacle

Steps for connecting the drain hose for non-gravity drain systems.

Standpipe Installation

Gravity Drain Models - Connect Drain Outlet to Drain System

Steps for connecting the drain hose for gravity drain systems.

Position and Level the Washer

Procedures for correctly positioning and leveling the appliance for stable operation.

Connect the Washer to Electrical Power

General instructions for connecting the washer to the electrical supply.

Machine Must Be Hard Wired

Electrical Requirements

Earth;Ground Instructions

Critical information regarding proper grounding to prevent electric shock.

Check Installation

Operation

Load Laundry

Add Laundry Supplies

Set Fabric Selector;Wash Temperature (°C)

Set Soil Level

Start Washer

Maintenance

Replacing Hoses

Filter Screens

Cleaning Foreign Object Trap

Reinstallation of Shipping Materials

Troubleshooting

Troubleshooting Washer Symptoms

Provides solutions for common washer problems like "Won't Fill" or "Won't Drain".

Installer Checklist

A step-by-step checklist for installers to verify correct setup.