SPIT Pulsa 700E User Manual

Tsupport@itwcp.co.uk
www.itwcp.co.uk
Technical Helpline UK: 0800 731 4924
Technical Helpline ROI: 1 800 882 388
Pulsa Operator Guide
Safety instructions
GB
Not following the safety precautions may cause
injury to yourself or others. Strictly follow the
safety precautions.
Wear ear defenders.
Wear safety glasses.
Only use the tool for its intended use.
This is not a toy. Never point it at people.
Always assume that the tool is loaded.
Never transport the tool with your finger on the trigger.
Never place your hand over the nosepiece.
When servicing, remove the fuel cell, battery and nails from the magazine.
Warning: the contents of the fuel cell are flammable.
The fuel cell is under pressure. Protect it from temperatures above 50°C
(sunlight).
Do not open, puncture or burn the fuel cell.
Keep the fuel cell away from flames, sparks and heat. Do not spray near flames
or incandescent objects.
The fuel cell cannot be recharged. Do not attempt to fill or recycle it.
Place empty fuel cells in the bio-bag and send to SPIT After-Sales Service.
Keep tool, fuel cells and battery away from children.
Only use the tool in well-ventilated areas. Store the fuel cells in a well-ventilated
place.
For reasons of safety and operation, it is imperative that only SPIT-compatible
fuel cells and nails be used. SPIT does not license any other company to
manufacture fuel cells and nails and can only guarantee the quality and
performance of its own, genuine products. SPIT cannot accept responsibility for
damage or injury caused by the use of third party fuel cells and nails which are
not SPIT-compatible. In particular, your product warranty will not cover damage
to the Pulsa 700 caused by non-compatible parts.
Do not use the PULSA 700 in rainy or excessively humid conditions.
IMPORTANT INFORMATION ABOUT SAFETY REQUIREMENTS
The European Standard EN 792-13 has established certain safety requirements
for hand-help non-electric fastener driving tools and it requires the respective
instructions to be part of the tool operating manual. In your own interest, we urge
you to follow such safety requirements without exception.
SPIT Fastener driving tools operated by internal combustion shall only be used
with dispensers for combustible gas which are listed in the SPIT operating
instruction (Item 7.2.5a). For the SPIT Pulsa tool, this means the use of SPIT
specified Pulsa Fuel Cells.
Only those fasteners listed in the SPIT operating instruction may be used in the SPIT
fastener driving tool (Item 7.2.1a). The fastener driving tool and the fastener listed
in the operating instruction must be seen as one unit system in terms of safety.
Only the fuel cells and lubricants listed in the SPIT operating instruction may be
may be used (Item 7.2.1b).
For the maintenance of SPIT fastener driving tools, only spare parts specified by
the manufacturer or his authorized representative shall be used (Item 7.2.1e).
Safety instructions
GB
Not following the safety precautions may cause
injury to yourself or others. Strictly follow the
safety precautions.
Wear ear defenders.
Wear safety glasses.
Only use the tool for its intended use.
This is not a toy. Never point it at people.
Always assume that the tool is loaded.
Never transport the tool with your finger on the trigger.
Never place your hand over the nosepiece.
When servicing, remove the fuel cell, battery and nails from the magazine.
Warning: the contents of the fuel cell are flammable.
The fuel cell is under pressure. Protect it from temperatures above 50°C
(sunlight).
Do not open, puncture or burn the fuel cell.
Keep the fuel cell away from flames, sparks and heat. Do not spray near flames
or incandescent objects.
The fuel cell cannot be recharged. Do not attempt to fill or recycle it.
Place empty fuel cells in the bio-bag and send to SPIT After-Sales Service.
Keep tool, fuel cells and battery away from children.
Only use the tool in well-ventilated areas. Store the fuel cells in a well-ventilated
place.
For reasons of safety and operation, it is imperative that only SPIT-compatible
fuel cells and nails be used. SPIT does not license any other company to
manufacture fuel cells and nails and can only guarantee the quality and
performance of its own, genuine products. SPIT cannot accept responsibility for
damage or injury caused by the use of third party fuel cells and nails which are
not SPIT-compatible. In particular, your product warranty will not cover damage
to the Pulsa 700 caused by non-compatible parts.
Do not use the PULSA 700 in rainy or excessively humid conditions.
IMPORTANT INFORMATION ABOUT SAFETY REQUIREMENTS
The European Standard EN 792-13 has established certain safety requirements
for hand-help non-electric fastener driving tools and it requires the respective
instructions to be part of the tool operating manual. In your own interest, we urge
you to follow such safety requirements without exception.
SPIT Fastener driving tools operated by internal combustion shall only be used
with dispensers for combustible gas which are listed in the SPIT operating
instruction (Item 7.2.5a). For the SPIT Pulsa tool, this means the use of SPIT
specified Pulsa Fuel Cells.
Only those fasteners listed in the SPIT operating instruction may be used in the SPIT
fastener driving tool (Item 7.2.1a). The fastener driving tool and the fastener listed
in the operating instruction must be seen as one unit system in terms of safety.
Only the fuel cells and lubricants listed in the SPIT operating instruction may be
may be used (Item 7.2.1b).
For the maintenance of SPIT fastener driving tools, only spare parts specified by
the manufacturer or his authorized representative shall be used (Item 7.2.1e).
Safety instructions
GB
Not following the safety precautions may cause
injury to yourself or others. Strictly follow the
safety precautions.
Wear ear defenders.
Wear safety glasses.
Only use the tool for its intended use.
This is not a toy. Never point it at people.
Always assume that the tool is loaded.
Never transport the tool with your finger on the trigger.
Never place your hand over the nosepiece.
When servicing, remove the fuel cell, battery and nails from the magazine.
Warning: the contents of the fuel cell are flammable.
The fuel cell is under pressure. Protect it from temperatures above 50°C
(sunlight).
Do not open, puncture or burn the fuel cell.
Keep the fuel cell away from flames, sparks and heat. Do not spray near flames
or incandescent objects.
The fuel cell cannot be recharged. Do not attempt to fill or recycle it.
Place empty fuel cells in the bio-bag and send to SPIT After-Sales Service.
Keep tool, fuel cells and battery away from children.
Only use the tool in well-ventilated areas. Store the fuel cells in a well-ventilated
place.
For reasons of safety and operation, it is imperative that only SPIT-compatible
fuel cells and nails be used. SPIT does not license any other company to
manufacture fuel cells and nails and can only guarantee the quality and
performance of its own, genuine products. SPIT cannot accept responsibility for
damage or injury caused by the use of third party fuel cells and nails which are
not SPIT-compatible. In particular, your product warranty will not cover damage
to the Pulsa 700 caused by non-compatible parts.
Do not use the PULSA 700 in rainy or excessively humid conditions.
IMPORTANT INFORMATION ABOUT SAFETY REQUIREMENTS
The European Standard EN 792-13 has established certain safety requirements
for hand-help non-electric fastener driving tools and it requires the respective
instructions to be part of the tool operating manual. In your own interest, we urge
you to follow such safety requirements without exception.
SPIT Fastener driving tools operated by internal combustion shall only be used
with dispensers for combustible gas which are listed in the SPIT operating
instruction (Item 7.2.5a). For the SPIT Pulsa tool, this means the use of SPIT
specified Pulsa Fuel Cells.
Only those fasteners listed in the SPIT operating instruction may be used in the SPIT
fastener driving tool (Item 7.2.1a). The fastener driving tool and the fastener listed
in the operating instruction must be seen as one unit system in terms of safety.
Only the fuel cells and lubricants listed in the SPIT operating instruction may be
may be used (Item 7.2.1b).
For the maintenance of SPIT fastener driving tools, only spare parts specified by
the manufacturer or his authorized representative shall be used (Item 7.2.1e).
Safety instructions
GB
Not following the safety precautions may cause
injury to yourself or others. Strictly follow the
safety precautions.
Wear ear defenders.
Wear safety glasses.
Only use the tool for its intended use.
This is not a toy. Never point it at people.
Always assume that the tool is loaded.
Never transport the tool with your finger on the trigger.
Never place your hand over the nosepiece.
When servicing, remove the fuel cell, battery and nails from the magazine.
Warning: the contents of the fuel cell are flammable.
The fuel cell is under pressure. Protect it from temperatures above 50°C
(sunlight).
Do not open, puncture or burn the fuel cell.
Keep the fuel cell away from flames, sparks and heat. Do not spray near flames
or incandescent objects.
The fuel cell cannot be recharged. Do not attempt to fill or recycle it.
Place empty fuel cells in the bio-bag and send to SPIT After-Sales Service.
Keep tool, fuel cells and battery away from children.
Only use the tool in well-ventilated areas. Store the fuel cells in a well-ventilated
place.
For reasons of safety and operation, it is imperative that only SPIT-compatible
fuel cells and nails be used. SPIT does not license any other company to
manufacture fuel cells and nails and can only guarantee the quality and
performance of its own, genuine products. SPIT cannot accept responsibility for
damage or injury caused by the use of third party fuel cells and nails which are
not SPIT-compatible. In particular, your product warranty will not cover damage
to the Pulsa 700 caused by non-compatible parts.
Do not use the PULSA 700 in rainy or excessively humid conditions.
IMPORTANT INFORMATION ABOUT SAFETY REQUIREMENTS
The European Standard EN 792-13 has established certain safety requirements
for hand-help non-electric fastener driving tools and it requires the respective
instructions to be part of the tool operating manual. In your own interest, we urge
you to follow such safety requirements without exception.
SPIT Fastener driving tools operated by internal combustion shall only be used
with dispensers for combustible gas which are listed in the SPIT operating
instruction (Item 7.2.5a). For the SPIT Pulsa tool, this means the use of SPIT
specified Pulsa Fuel Cells.
Only those fasteners listed in the SPIT operating instruction may be used in the SPIT
fastener driving tool (Item 7.2.1a). The fastener driving tool and the fastener listed
in the operating instruction must be seen as one unit system in terms of safety.
Only the fuel cells and lubricants listed in the SPIT operating instruction may be
may be used (Item 7.2.1b).
For the maintenance of SPIT fastener driving tools, only spare parts specified by
the manufacturer or his authorized representative shall be used (Item 7.2.1e).
Safety instructions
GB
Not following the safety precautions may cause
injury to yourself or others. Strictly follow the
safety precautions.
Wear ear defenders.
Wear safety glasses.
Only use the tool for its intended use.
This is not a toy. Never point it at people.
Always assume that the tool is loaded.
Never transport the tool with your finger on the trigger.
Never place your hand over the nosepiece.
When servicing, remove the fuel cell, battery and nails from the magazine.
Warning: the contents of the fuel cell are flammable.
The fuel cell is under pressure. Protect it from temperatures above 50°C
(sunlight).
Do not open, puncture or burn the fuel cell.
Keep the fuel cell away from flames, sparks and heat. Do not spray near flames
or incandescent objects.
The fuel cell cannot be recharged. Do not attempt to fill or recycle it.
Place empty fuel cells in the bio-bag and send to SPIT After-Sales Service.
Keep tool, fuel cells and battery away from children.
Only use the tool in well-ventilated areas. Store the fuel cells in a well-ventilated
place.
For reasons of safety and operation, it is imperative that only SPIT-compatible
fuel cells and nails be used. SPIT does not license any other company to
manufacture fuel cells and nails and can only guarantee the quality and
performance of its own, genuine products. SPIT cannot accept responsibility for
damage or injury caused by the use of third party fuel cells and nails which are
not SPIT-compatible. In particular, your product warranty will not cover damage
to the Pulsa 700 caused by non-compatible parts.
Do not use the PULSA 700 in rainy or excessively humid conditions.
IMPORTANT INFORMATION ABOUT SAFETY REQUIREMENTS
The European Standard EN 792-13 has established certain safety requirements
for hand-help non-electric fastener driving tools and it requires the respective
instructions to be part of the tool operating manual. In your own interest, we urge
you to follow such safety requirements without exception.
SPIT Fastener driving tools operated by internal combustion shall only be used
with dispensers for combustible gas which are listed in the SPIT operating
instruction (Item 7.2.5a). For the SPIT Pulsa tool, this means the use of SPIT
specified Pulsa Fuel Cells.
Only those fasteners listed in the SPIT operating instruction may be used in the SPIT
fastener driving tool (Item 7.2.1a). The fastener driving tool and the fastener listed
in the operating instruction must be seen as one unit system in terms of safety.
Only the fuel cells and lubricants listed in the SPIT operating instruction may be
may be used (Item 7.2.1b).
For the maintenance of SPIT fastener driving tools, only spare parts specified by
the manufacturer or his authorized representative shall be used (Item 7.2.1e).
Safety instructions
GB
Not following the safety precautions may cause
injury to yourself or others. Strictly follow the
safety precautions.
Wear ear defenders.
Wear safety glasses.
Only use the tool for its intended use.
This is not a toy. Never point it at people.
Always assume that the tool is loaded.
Never transport the tool with your finger on the trigger.
Never place your hand over the nosepiece.
When servicing, remove the fuel cell, battery and nails from the magazine.
Warning: the contents of the fuel cell are flammable.
The fuel cell is under pressure. Protect it from temperatures above 50°C
(sunlight).
Do not open, puncture or burn the fuel cell.
Keep the fuel cell away from flames, sparks and heat. Do not spray near flames
or incandescent objects.
The fuel cell cannot be recharged. Do not attempt to fill or recycle it.
Place empty fuel cells in the bio-bag and send to SPIT After-Sales Service.
Keep tool, fuel cells and battery away from children.
Only use the tool in well-ventilated areas. Store the fuel cells in a well-ventilated
place.
For reasons of safety and operation, it is imperative that only SPIT-compatible
fuel cells and nails be used. SPIT does not license any other company to
manufacture fuel cells and nails and can only guarantee the quality and
performance of its own, genuine products. SPIT cannot accept responsibility for
damage or injury caused by the use of third party fuel cells and nails which are
not SPIT-compatible. In particular, your product warranty will not cover damage
to the Pulsa 700 caused by non-compatible parts.
Do not use the PULSA 700 in rainy or excessively humid conditions.
IMPORTANT INFORMATION ABOUT SAFETY REQUIREMENTS
The European Standard EN 792-13 has established certain safety requirements
for hand-help non-electric fastener driving tools and it requires the respective
instructions to be part of the tool operating manual. In your own interest, we urge
you to follow such safety requirements without exception.
SPIT Fastener driving tools operated by internal combustion shall only be used
with dispensers for combustible gas which are listed in the SPIT operating
instruction (Item 7.2.5a). For the SPIT Pulsa tool, this means the use of SPIT
specified Pulsa Fuel Cells.
Only those fasteners listed in the SPIT operating instruction may be used in the SPIT
fastener driving tool (Item 7.2.1a). The fastener driving tool and the fastener listed
in the operating instruction must be seen as one unit system in terms of safety.
Only the fuel cells and lubricants listed in the SPIT operating instruction may be
may be used (Item 7.2.1b).
For the maintenance of SPIT fastener driving tools, only spare parts specified by
the manufacturer or his authorized representative shall be used (Item 7.2.1e).
Safety instructions
GB
Not following the safety precautions may cause
injury to yourself or others. Strictly follow the
safety precautions.
Wear ear defenders.
Wear safety glasses.
Only use the tool for its intended use.
This is not a toy. Never point it at people.
Always assume that the tool is loaded.
Never transport the tool with your finger on the trigger.
Never place your hand over the nosepiece.
When servicing, remove the fuel cell, battery and nails from the magazine.
Warning: the contents of the fuel cell are flammable.
The fuel cell is under pressure. Protect it from temperatures above 50°C
(sunlight).
Do not open, puncture or burn the fuel cell.
Keep the fuel cell away from flames, sparks and heat. Do not spray near flames
or incandescent objects.
The fuel cell cannot be recharged. Do not attempt to fill or recycle it.
Place empty fuel cells in the bio-bag and send to SPIT After-Sales Service.
Keep tool, fuel cells and battery away from children.
Only use the tool in well-ventilated areas. Store the fuel cells in a well-ventilated
place.
For reasons of safety and operation, it is imperative that only SPIT-compatible
fuel cells and nails be used. SPIT does not license any other company to
manufacture fuel cells and nails and can only guarantee the quality and
performance of its own, genuine products. SPIT cannot accept responsibility for
damage or injury caused by the use of third party fuel cells and nails which are
not SPIT-compatible. In particular, your product warranty will not cover damage
to the Pulsa 700 caused by non-compatible parts.
Do not use the PULSA 700 in rainy or excessively humid conditions.
IMPORTANT INFORMATION ABOUT SAFETY REQUIREMENTS
The European Standard EN 792-13 has established certain safety requirements
for hand-help non-electric fastener driving tools and it requires the respective
instructions to be part of the tool operating manual. In your own interest, we urge
you to follow such safety requirements without exception.
SPIT Fastener driving tools operated by internal combustion shall only be used
with dispensers for combustible gas which are listed in the SPIT operating
instruction (Item 7.2.5a). For the SPIT Pulsa tool, this means the use of SPIT
specified Pulsa Fuel Cells.
Only those fasteners listed in the SPIT operating instruction may be used in the SPIT
fastener driving tool (Item 7.2.1a). The fastener driving tool and the fastener listed
in the operating instruction must be seen as one unit system in terms of safety.
Only the fuel cells and lubricants listed in the SPIT operating instruction may be
may be used (Item 7.2.1b).
For the maintenance of SPIT fastener driving tools, only spare parts specified by
the manufacturer or his authorized representative shall be used (Item 7.2.1e).
01

SPIT Pulsa 700E Specifications

General

Brand	SPIT
Model	Pulsa 700E
Category	Nail Gun
Language	English

Summary

Safety Instructions

General Safety Precautions

Key safety rules for tool operation and user protection.

Fuel Cell Handling & Safety

Specific warnings and handling instructions for the flammable fuel cell.

Product Compatibility Mandates

Mandates use of SPIT-compatible fuel cells and nails for safety and warranty.

Safety Standards & Requirements

EN 792-13 Compliance

European standard requirements for fastener driving tools.

SPIT Specified Consumables

Importance of using specified fuel cells, nails, and lubricants.

PULSA Consumables

Fuel Cell Specifications

Details on fuel cell temperature limits, pressure, and replacement.

SPIT Nails Usage Guidelines

Requirement to use only SPIT branded nails with the tool.

Battery Management

Battery Charging & Initial Use

Instructions for charging, initial use, and battery discharge.

Battery Status Indicator

Explains the meaning of the LED light states after battery installation.

Installing Fuel Cell and Nails

Fuel Cell Installation Procedure

Steps to insert and secure the fuel cell into the tool.

Loading Nail Strips

Procedure for loading nail strips into the magazine.

Tool Operation Guide

Operating Positions (Wall, Floor, Ceiling)

Demonstrates tool use in wall, floor, and ceiling applications.

Compatible Base Materials

Lists and illustrates materials compatible with the tool.

Firing Mechanism

Steps for placing the tool and pulling the trigger to fire.

Advanced Tool Use

Using Without Nail Magazine

How to use the tool with the nail magazine removed.

Protective Cover Operations

Instructions for fitting or removing the protective cover.

Adjusting Nail Depth and Accessories

Setting Pin Guide Depth

How to set the pin guide for nail insertion depth.

Metal Washer Holder Installation (700P)

Instructions for mounting the optional metal washer holder.

Servicing and Troubleshooting

User Maintenance Tasks

Basic maintenance tasks like cleaning filters and contacts.

Malfunction Solutions

Troubleshooting guide for common tool issues and their solutions.