Need help?Do you have a question about the Standard Change-Makers BX Series and is the answer not in the manual?
General| Brand | Standard Change-Makers |
|---|---|
| Model | BX Series |
| Category | Cash Counters & Coin Sorters |
| Language | English |
Guidance on selecting an appropriate location for the machine to ensure accessibility and security.
Instructions for removing shipping restraints to access internal components and ensure proper operation.
Details on connecting the machine to a power source, including recommendations for dedicated lines and surge protectors.
Step-by-step guide for loading coins into the dispenser, including capacity information.
Instructions for loading bills into the dispenser, emphasizing bill condition and proper handling.
Procedures for verifying the machine is ready for operation and performing initial tests.
Guide to identifying and resolving dispenser error conditions using flash codes and troubleshooting charts.
Instructions on how to reset a dispenser to clear error conditions and restore normal operation.
Guide on how to safely remove bills from the bill acceptor's collection box.
Instructions for emptying coins from the dispenser using bulk or electronic dump methods.
Steps for emptying the coin acceptor box when it becomes full.
Information on operating voltage, power consumption, and electrical service requirements for the machine.
Guidelines for machine placement concerning temperature, dirt, and moisture to ensure proper operation.
Information on the performance and life limitations of the bill acceptor based on manufacturer specifications.
Guidelines for optimal performance and lifespan of the bill dispenser, considering environmental factors.
General guidelines for installing the machine cabinet, referencing a specific installation manual.
Factors to consider when locating the changer, including service access and ADA compliance.
Instructions for installing the machine using an optional base.
Guidance on mounting the changer on walls, considering wall construction for security.
Instructions and considerations for installing rear-load changer cabinets, including support requirements.
Steps for securely mounting the changer cabinet, emphasizing level installation and cleanliness.
Detailed instructions for connecting the machine's electrical supply, emphasizing grounding and dedicated lines.
Procedures for checking voltage and polarity of the power source to ensure proper machine operation.
Explanation of how to operate the T-handle lock mechanism for accessing the changer.
Description of the Dual Redundancy mode for improved machine reliability with multiple acceptors.
Settings for controlling bill acceptance and security levels for enhanced fraud prevention.
Feature to automatically shut off the machine after a period of high bill deposits to prevent loss.
Automatic reset feature for certain error conditions after a predetermined time period.
Configuration for serial communication protocol for authorized projects and computer integration.
Feature to clear all errors upon a power cycle.
Allows holding or clearing an unpaid balance (escrow) for the next deposit.
Capability to transfer owed amounts from a faulty or sold-out dispenser to others.
Allows forcing a specific dispense quantity from the Primary Device, managing remaining amounts.
Feature to ignore Forced Dispense settings under specific deposit circumstances.
Ensures dispense occurs only after enough money is accepted to meet or exceed the Primary Device value.
Sets the type of dispenser (e.g., coin, bill, token) for correct machine operation.
Selects the specific Bill Dispenser model for correct communication and options.
Configures the sensitivity level for detecting bill stringing attempts.
Option to count dispensed items by number instead of by dollar amount.
Forces the machine offline if the bill acceptor is unavailable, unless another acceptor is present.
Forces the machine offline if the coin acceptor is unavailable, unless another acceptor is present.
Overrides default payout to dispense from a lower denomination dispenser for specific BX models.
Enables checking for Mylar bills from a Fujitsu bill dispenser.
Automatically clears overpay errors, potentially hiding underlying issues.
Allows issuing bonus tokens with larger token purchases or specific bill deposits.
Sets the value for items dispensed by ticket, token, or card dispensers, and multi-cassette bill dispensers.
Adjusts the time the ticket device remains active after the last ticket notch is detected.
Factor used when the ticket dispenser is empty, to transfer dispensing to another device.
Counts each notch as one ticket, used for applications dispensing multiple tickets per notch.
Decreases the number of bills remaining before reporting a bin as sold out.
Maximizes dispense capacity by disabling sold-out detectors for cassettes.
Explains how to interpret flash codes displayed by the yellow status LED for error identification.
A chart to assist in troubleshooting common failures not requiring factory repair.
Answers to common questions regarding machine operation, bill acceptance, and software upgrades.
Procedures for removing modules for repair and cleaning bill acceptors and coin/token hoppers.
Details on the optional electromechanical counter that tracks dispensed items.
Setting the sold-out level to prevent short pays, matching the largest bill denomination.
Specific instructions and information for the Fujitsu Bill Dispenser.
Explanation of how cassette magnets identify position, not denomination, for correct installation.
Step-by-step guide to setting cartridge position magnets to ensure correct cassette placement.
Locating and setting magnets on cassettes to verify correct installation in the dispenser.
Programming the denomination for each cassette into the bill dispenser controller memory.
List of available bill acceptor part numbers and their descriptions.
Part numbers and descriptions for various interconnecting cables used in the machine.
Information on coin acceptor kits, including contents and part numbers.
Listing of various miscellaneous parts available for the machine.
Part numbers for different coin dispenser hopper configurations.
Detailed part numbers for coin dispenser components like feed mechanisms and housings.
Detailed specifications, dimensions, and component locations for the MC100 model.
Detailed specifications, dimensions, and component locations for the MC200 model.
Detailed specifications, dimensions, and component locations for the MC300-RL model.
Detailed specifications, dimensions, and component locations for the MC400-RL model.
Specifications, dimensions, and component locations for multiple MC500-series models.
Detailed specifications, dimensions, and component locations for the MC600-RL model.
Detailed specifications, dimensions, and component locations for the MC700 model.
Detailed specifications, dimensions, and component locations for the MC800 model.
Detailed specifications, dimensions, and component locations for the MC900 model.
Specifications, dimensions, and component locations for the BX1010 (Fujitsu) model.
Specifications, dimensions, and component locations for the BX1010-RL (Fujitsu) model.
Specifications, dimensions, and component locations for the BX1010-FL (Fujitsu) model.
Specifications, dimensions, and component locations for the BCX2010-RL (Fujitsu) model.
Procedure to reset all feature settings back to their original factory default values.
Detailed switch settings for configuring bill acceptance and security levels.
Detailed switch settings for configuring the Fast Vend Shutoff feature.
Detailed switch settings for configuring the Error Timeout feature.
Detailed switch settings for configuring the Serial Control Level.
Detailed switch settings for configuring the Power Reset feature.
Detailed switch settings for configuring the Hold Escrow feature.
Detailed switch settings for configuring the Dispenser Transfer feature.
Detailed switch settings for configuring the Forced Dispense Feature.
Detailed switch settings for configuring the Forced Dispense Override feature.
Detailed switch settings for configuring the Accumulate Feature.
Detailed switch settings for configuring the Dispenser Type.
Detailed switch settings for configuring the Dispenser Sub Type.
Detailed switch settings for configuring the Stringing Detection Level.
Detailed switch settings for configuring the Count Items Out feature.
Detailed switch settings for configuring the No Bill Acceptor Shutdown.
Detailed switch settings for configuring the No Coin Acceptor Shutdown.
Detailed switch settings for configuring the Like Value Override feature.
Detailed switch settings for configuring the Mylar Note Check feature.
Detailed switch settings for configuring the Overpay Timeout feature.
Detailed switch settings for configuring the Bonus Tokens feature.
Detailed switch settings for configuring the Dispenser Value.
Detailed switch settings for configuring the Ticket Coast Time.
Detailed switch settings for configuring the Ticket Transfer Factor.
Detailed switch settings for configuring Tickets Per Notch.
Detailed switch settings for configuring the Bin Low Count Value.
Detailed switch settings for configuring the Bin Low Override Feature.
Contact information for the central region factory and home office service center.
To Next Page
