8
ENGLISH
uprights. Note that Part 2 should be positioned as shown in
Fig. B4. Connect Part 4 (top cross support) to the top of the
frame. Note that Part 4 should be positioned as shown in
Fig. B4.
Step 4
Now place and connect the ends of the top and center frame
supports to the frame. Take care to ensure that the supports
are positioned as shown in Fig. B5.
Step 5
Once you are satisfied that the frame is assembled correctly,
fully tighten ALL the bolts. Finally, assemble the 4 foot pads to
the bottom of each leg (see Fig. B6).
2. Assemble the stand’s legs
Step 1
Select the following parts:
2 x Part 1
1 x Part 3
1 x Part 5
Lay the parts together as shown in Fig. B1, B2, and B3. This
is best done by simply laying the parts loosely together on the
floor. Once you are satisfied that you have the parts correctly
laid together, start the fitting process.
Align the holes and secure with the bolts as shown in
Fig. B1.
DO NOT fully tighten the bolts, nuts and washers at this point.
Finger tight is sufficient.
Step 2
Repeat Step 1 so that there are two frames assembled.
Step 3
Select the following parts:
2 x Part 2
2 x Part 4
These will form the crosspieces between the previously
assembled frames. Lay the parts flat on the floor. Connect the
longer Part (2) and fix it to the frame in the center of the
B1
B2
B3
B1
5
3
2
4
B4
1
Langkah 4
Sekarang tempatkan dan sambungkan bagian ujung atas dan
tengah penyangga kerangka ke kerangka. Berhati-hatilah
untuk memastikan bahwa penyangga diposisikan seperti yang
ditunjukkan dalam Gbr. B5.
8
ENGLISH
uprights. Note that Part 2 should be positioned as shown in
Fig. B4. Connect Part 4 (top cross support) to the top of the
frame. Note that Part 4 should be positioned as shown in
Fig. B4.
Step 4
Now place and connect the ends of the top and center frame
supports to the frame. Take care to ensure that the supports
are positioned as shown in Fig. B5.
Step 5
Once you are satisfied that the frame is assembled correctly,
fully tighten ALL the bolts. Finally, assemble the 4 foot pads to
the bottom of each leg (see Fig. B6).
2. Assemble the stand’s legs
Step 1
Select the following parts:
2 x Part 1
1 x Part 3
1 x Part 5
Lay the parts together as shown in Fig. B1, B2, and B3. This
is best done by simply laying the parts loosely together on the
floor. Once you are satisfied that you have the parts correctly
laid together, start the fitting process.
Align the holes and secure with the bolts as shown in
Fig. B1.
DO NOT fully tighten the bolts, nuts and washers at this point.
Finger tight is sufficient.
Step 2
Repeat Step 1 so that there are two frames assembled.
Step 3
Select the following parts:
2 x Part 2
2 x Part 4
These will form the crosspieces between the previously
assembled frames. Lay the parts flat on the floor. Connect the
longer Part (2) and fix it to the frame in the center of the
B1
B2
B3
B1
5
3
2
4
B4
1
B6
5
1
4
B5
Langkah 5
Setelah Anda senang bahwa kerangka dirakit dengan benar,
kencangkan erat-erat SEMUA baut. Terakhir, rakitlah bantalan
4 kaki ke bagian bawah dari masing-masing kaki (lihat
Gbr. B6).
8
ENGLISH
uprights. Note that Part 2 should be positioned as shown in
Fig. B4. Connect Part 4 (top cross support) to the top of the
frame. Note that Part 4 should be positioned as shown in
Fig. B4.
Step 4
Now place and connect the ends of the top and center frame
supports to the frame. Take care to ensure that the supports
are positioned as shown in Fig. B5.
Step 5
Once you are satisfied that the frame is assembled correctly,
fully tighten ALL the bolts. Finally, assemble the 4 foot pads to
the bottom of each leg (see Fig. B6).
2. Assemble the stand’s legs
Step 1
Select the following parts:
2 x Part 1
1 x Part 3
1 x Part 5
Lay the parts together as shown in Fig. B1, B2, and B3. This
is best done by simply laying the parts loosely together on the
floor. Once you are satisfied that you have the parts correctly
laid together, start the fitting process.
Align the holes and secure with the bolts as shown in
Fig. B1.
DO NOT fully tighten the bolts, nuts and washers at this point.
Finger tight is sufficient.
Step 2
Repeat Step 1 so that there are two frames assembled.
Step 3
Select the following parts:
2 x Part 2
2 x Part 4
These will form the crosspieces between the previously
assembled frames. Lay the parts flat on the floor. Connect the
longer Part (2) and fix it to the frame in the center of the
B1
B2
B3
B1
5
3
2
4
B4
1
B6
Luruskan lubang dan kencangkan dengan baut seperti yang
ditunjukkan di
Gbr. B1.
JANGAN kencangkan baut, mur, dan ring sepenuhnya pada
tahap ini. Cukup kencangkan dengan jari.
Langkah 2
Ulangi Langkah 1, sehingga hanya ada dua kerangka yang
dirakit.
8
ENGLISH
uprights. Note that Part 2 should be positioned as shown in
Fig. B4. Connect Part 4 (top cross support) to the top of the
frame. Note that Part 4 should be positioned as shown in
Fig. B4.
Step 4
Now place and connect the ends of the top and center frame
supports to the frame. Take care to ensure that the supports
are positioned as shown in Fig. B5.
Step 5
Once you are satisfied that the frame is assembled correctly,
fully tighten ALL the bolts. Finally, assemble the 4 foot pads to
the bottom of each leg (see Fig. B6).
2. Assemble the stand’s legs
Step 1
Select the following parts:
2 x Part 1
1 x Part 3
1 x Part 5
Lay the parts together as shown in Fig. B1, B2, and B3. This
is best done by simply laying the parts loosely together on the
floor. Once you are satisfied that you have the parts correctly
laid together, start the fitting process.
Align the holes and secure with the bolts as shown in
Fig. B1.
DO NOT fully tighten the bolts, nuts and washers at this point.
Finger tight is sufficient.
Step 2
Repeat Step 1 so that there are two frames assembled.
Step 3
Select the following parts:
2 x Part 2
2 x Part 4
These will form the crosspieces between the previously
assembled frames. Lay the parts flat on the floor. Connect the
longer Part (2) and fix it to the frame in the center of the
B1
B2
B3
B1
Langkah 3
Pilih bagian berikut:
2 x Bagian 2
2 x Bagian 4
Bagian ini akan membentuk bagian silang antara kerangka
yang dirakit sebelumnya. Letakkan bagian di lantai yang datar.
Sambungkan Bagian (2) yang lebih panjang dan kencangkan
pada kerangka di bagian tengah penyangga. Perhatikan
bahwa Bagian 2 harus diposisikan seperti yang ditunjukkan
dalam Gbr. B4. Sambungkan Bagian 4 (penyangga silang
bagian atas) ke bagian atas kerangka. Perhatikan bahwa
Bagian 4 harus diposisikan seperti yang ditunjukkan dalam
Gbr. B4.
BAHASA INDONESIA
34
To Next Page
Loading...
