Stanley SST1801 - Page 36

3. Longgarkan pegangan pengunci (f) dan dorong pisau
pembelah (3) di posisi atas (Gbr.F)
10
ENGLISH
Saw blade assembly/replacement (Fig E, H, I)
1. WARNING: Ensure the machine is disconnected from the
power source. Wear the safety gloves.
2. Disassemble the saw blade guard (2) (Fig. H.)
3. Remove the table insert (20) (Fig. E).
4. Loosen the nut by placing the spanner wrench (17) on the
nut and countering with another spanner wrench (17) on
the flange (Fig. I).
5. WARNING! Turn the nut in the rotational direction of the
saw blade.
6. Remove the outer flange and take out the saw blade from
the inner flange, with diagonally downwards movement.
7. Carefully clean the flange with a cloth before fixing the
new saw blade.
8. Insert the new saw blade and fasten the outer flange. The
outer flange has a Φ25.4mm raised boss which fits in side
the blade bore.
WARNING! The teeth of a new blade are very sharp and can
be dangerous. Make sure the teeth point down at the front of
the table, aligned with the arrow marked on the saw blade
guard (2).
9. Attach the table insert (20) and the saw blade guard (2)
again and set them.
10. Before working, check the functionality of the guards.
On/Off switch (Fig. J)
- To switch the machine on, press the green start “I” button.
- To switch the machine off, press the red stop “O” button.
Cutting depth (Fig J)
Turn the blade elevation handle (11) to set the blade to the
required cutting depth.
4. The gap between the saw blade (4) teeth and the riving
knife should be around 3mm to 5mm (Fig.G)
5. R-tighten the mounting screw (f) and fix the table insert
(20)
WARNING! Ensure the machine is disconnected
from the power source. Never use the machine
without the table insert; Immediately replace the
table insert when worn or damaged
Saw blade guard assembly (Fig H)
1. Fasten the saw blade guard (2) to the riving knife (3) with
the bolt (g).
2. Disassembly in reverse order.
f
34
F
G
MAX 3-5
17
17
I
8
11
10
J
2 3
g
H
4. Celah antara gerigi bilah gergaji (4) dan pisau pembelah
harus sekitar 3 mm hingga 5 mm (Gbr.G)
10
ENGLISH
Saw blade assembly/replacement (Fig E, H, I)
1. WARNING: Ensure the machine is disconnected from the
power source. Wear the safety gloves.
2. Disassemble the saw blade guard (2) (Fig. H.)
3. Remove the table insert (20) (Fig. E).
4. Loosen the nut by placing the spanner wrench (17) on the
nut and countering with another spanner wrench (17) on
the flange (Fig. I).
5. WARNING! Turn the nut in the rotational direction of the
saw blade.
6. Remove the outer flange and take out the saw blade from
the inner flange, with diagonally downwards movement.
7. Carefully clean the flange with a cloth before fixing the
new saw blade.
8. Insert the new saw blade and fasten the outer flange. The
outer flange has a Φ25.4mm raised boss which fits in side
the blade bore.
WARNING! The teeth of a new blade are very sharp and can
be dangerous. Make sure the teeth point down at the front of
the table, aligned with the arrow marked on the saw blade
guard (2).
9. Attach the table insert (20) and the saw blade guard (2)
again and set them.
10. Before working, check the functionality of the guards.
On/Off switch (Fig. J)
- To switch the machine on, press the green start “I” button.
- To switch the machine off, press the red stop “O” button.
Cutting depth (Fig J)
Turn the blade elevation handle (11) to set the blade to the
required cutting depth.
4. The gap between the saw blade (4) teeth and the riving
knife should be around 3mm to 5mm (Fig.G)
5. R-tighten the mounting screw (f) and fix the table insert
(20)
WARNING! Ensure the machine is disconnected
from the power source. Never use the machine
without the table insert; Immediately replace the
table insert when worn or damaged
Saw blade guard assembly (Fig H)
1. Fasten the saw blade guard (2) to the riving knife (3) with
the bolt (g).
2. Disassembly in reverse order.
f
34
F
G
MAX 3-5
17
17
I
8
11
10
J
2 3
g
H
5. Kencangkan kembali sekrup pemasangan (f) dan pasang
sisipan meja (20)
PERINGATAN! Pastikan mesin terputus dari sumber
listrik. Jangan sekali-kali menggunakan mesin tanpa
sisipan meja; Segera ganti sisipan meja saat aus
atau rusak
Rakitan pengaman bilah gergaji (Gbr H)
1. Kencangkan pengaman bilah gergaji (2) ke pisau
pembelah (3) dengan baut (g).
2. Bongkar dengan urutan secara terbalik.
10
ENGLISH
Saw blade assembly/replacement (Fig E, H, I)
1. WARNING: Ensure the machine is disconnected from the
power source. Wear the safety gloves.
2. Disassemble the saw blade guard (2) (Fig. H.)
3. Remove the table insert (20) (Fig. E).
4. Loosen the nut by placing the spanner wrench (17) on the
nut and countering with another spanner wrench (17) on
the flange (Fig. I).
5. WARNING! Turn the nut in the rotational direction of the
saw blade.
6. Remove the outer flange and take out the saw blade from
the inner flange, with diagonally downwards movement.
7. Carefully clean the flange with a cloth before fixing the
new saw blade.
8. Insert the new saw blade and fasten the outer flange. The
outer flange has a Φ25.4mm raised boss which fits in side
the blade bore.
WARNING! The teeth of a new blade are very sharp and can
be dangerous. Make sure the teeth point down at the front of
the table, aligned with the arrow marked on the saw blade
guard (2).
9. Attach the table insert (20) and the saw blade guard (2)
again and set them.
10. Before working, check the functionality of the guards.
On/Off switch (Fig. J)
- To switch the machine on, press the green start “I” button.
- To switch the machine off, press the red stop “O” button.
Cutting depth (Fig J)
Turn the blade elevation handle (11) to set the blade to the
required cutting depth.
4. The gap between the saw blade (4) teeth and the riving
knife should be around 3mm to 5mm (Fig.G)
5. R-tighten the mounting screw (f) and fix the table insert
(20)
WARNING! Ensure the machine is disconnected
from the power source. Never use the machine
without the table insert; Immediately replace the
table insert when worn or damaged
Saw blade guard assembly (Fig H)
1. Fasten the saw blade guard (2) to the riving knife (3) with
the bolt (g).
2. Disassembly in reverse order.
f
34
F
G
MAX 3-5
17
17
I
8
11
10
J
2 3
g
H
Perakitan/penggantian gergaji (Gbr E, H, I)
1. PERINGATAN: Pastikan mesin terputus dari sumber
listrik. Gunakan sarung tangan keselamatan.
2. Bongkar pengaman bilah gergaji (2) (Gbr. H.)
3. Ambil sisipan meja (20) (Gbr. E).
4. Longgarkan mur dengan menempatkan kunci perentang
(17) pada mur dan berlawanan arah dengan kunci
perentang lainnya (17) pada pinggiran (Gbr. I).
10
ENGLISH
Saw blade assembly/replacement (Fig E, H, I)
1. WARNING: Ensure the machine is disconnected from the
power source. Wear the safety gloves.
2. Disassemble the saw blade guard (2) (Fig. H.)
3. Remove the table insert (20) (Fig. E).
4. Loosen the nut by placing the spanner wrench (17) on the
nut and countering with another spanner wrench (17) on
the flange (Fig. I).
5. WARNING! Turn the nut in the rotational direction of the
saw blade.
6. Remove the outer flange and take out the saw blade from
the inner flange, with diagonally downwards movement.
7. Carefully clean the flange with a cloth before fixing the
new saw blade.
8. Insert the new saw blade and fasten the outer flange. The
outer flange has a Φ25.4mm raised boss which fits in side
the blade bore.
WARNING! The teeth of a new blade are very sharp and can
be dangerous. Make sure the teeth point down at the front of
the table, aligned with the arrow marked on the saw blade
guard (2).
9. Attach the table insert (20) and the saw blade guard (2)
again and set them.
10. Before working, check the functionality of the guards.
On/Off switch (Fig. J)
- To switch the machine on, press the green start “I” button.
- To switch the machine off, press the red stop “O” button.
Cutting depth (Fig J)
Turn the blade elevation handle (11) to set the blade to the
required cutting depth.
4. The gap between the saw blade (4) teeth and the riving
knife should be around 3mm to 5mm (Fig.G)
5. R-tighten the mounting screw (f) and fix the table insert
(20)
WARNING! Ensure the machine is disconnected
from the power source. Never use the machine
without the table insert; Immediately replace the
table insert when worn or damaged
Saw blade guard assembly (Fig H)
1. Fasten the saw blade guard (2) to the riving knife (3) with
the bolt (g).
2. Disassembly in reverse order.
f
34
F
G
MAX 3-5
17
17
I
8
11
10
J
2 3
g
H
5. PERINGATAN! Putar mur ke arah rotasi bilah gergaji.
6. Lepaskan pinggiran bagian luar dan keluarkan bilah
gergaji dari pinggiran bagian dalam, dengan gerakan ke
bawah secara diagonal.
7. Bersihkan pinggiran dengan hati-hati menggunakan kain
sebelum menempelkan bilah gergaji yang baru.
8. Masukkan bilah gergaji baru dan kencangkan pinggiran
bagian luar. Pinggiran bagian luar memiliki ujung
terangkat sebesar Φ25,4mm yang pas pada samping
lubang bilah.
PERINGATAN! gerigi bilah yang baru sangat tajam dan dapat
berbahaya. Pastikan gerigi mengarah ke bawah di depan meja,
sejajar dengan panah yang ditandai pada pengaman bilah
gergaji (2).
9. Pasang kembali sisipan meja (20) dan pengaman bilah
gergaji (2) dan aturlah.
10. Sebelum bekerja, periksa fungsionalitas pengaman.
MAKS 3-5
11
BAHASA INDONESIA
BAHASA INDONESIA
36