165
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
2.8 OPERATION SAFETY WARNINGS
• Check the product, its power plug and wire as well as accessories for
damage before each use. Do not use the product if it is damaged or shows
wear.
• Double check that the accessories and attachments are properly fixed.
• Always hold the product on its handle. Keep the handle dry to ensure safe
support.
• Ensure that the air vents are always unobstructed and clear. Clean them
if necessary with a soft brush. Blocked air vents may lead to overheating and
damage the product.
• Switch the product o immediately if you are disturbed while working
by other people entering the working area. Always let the product come to
complete stop before putting it down.
• Do not overwork yourself. Take regular breaks to ensure you can
concentrate on the work and have full control over the product.
• Before switching the product on, check whether it has been assembled
correctly and all the moving parts are running smoothly.
• Operate the product only at reasonable hours – not early in the morning or
late at night when people might be disturbed.
• Avoid using the product in bad weather conditions, especially when there
is a risk of lightning. Do not operate the product in poor lighting. The operator
requires a clear view of the work area to identify potential hazards.
• Use of hearing protection reduces the ability to hear warnings (shouts
or alarms). The operator must pay extra attention to what is going on in the
work area. Do not get distracted, and always concentrate on the task.
• Operating similar tools nearby increases both the risk of hearing injury
and the potential for other persons to enter your work area.
• Walk, never run. Keep all parts of your body away from any moving part.
• Never run the product without the proper equipment attached.
• Do not modify the product in any way or use parts and accessories that are
not recommended by the manufacturer.
IF THE PRODUCT IS DROPPED, SUFFERS HEAVY IMPACT OR
BEGINS TO VIBRATE ABNORMALLY, IMMEDIATELY STOP THE
PRODUCT AND INSPECT FOR DAMAGE OR IDENTIFY THE CAUSE
OF THE VIBRATION. ANY DAMAGE SHOULD BE PROPERLY
REPAIRED OR REPLACE BY AN AUTHORIZED SERVICE CENTRE.
• To reduce the risk of injury associated with contacting rotating parts,
always stop the machine, disconnect the power plug, and make sure all
moving parts have stopped:
- before cleaning or clearing a blockage
- when leaving the product unattended
- before installing or removing attachments
- before checking, maintaining or working on the product
2.9 GRASS TRIMMER USE AND CARE
• Use this grass trimmer only for the purposes it was designed, do not aim
the grass trimmer at any people or animals.
• Remove the power plug whenever the machine is left by the user;
before clearing a blockage; before checking, cleaning or working on the
machine; after striking a foreign object to inspect the machine for damage;
if the machine starts to vibrate abnormally, for immediately check; during
transportation and during storage.
• Store grass trimmers indoors – when not in use, grass trimmer should be
stored indoors in dry, locked-up place – out of reach of children.
• Keep all parts of the body away from the trimmings spool. Make sure the
switch is o when clearing jammed material. A moment of inattention while
operating the grass trimmer may result in serious personal injury.
• Carry the grass trimmer by the handle with the trimming spool stopped.
Proper handling of the grass trimmer will reduce possible personal injury
from the trimming spool.
• Hold the power tool by insulated gripping surfaces only,.
• Hold the grass trimmer properly, with both hands. Loss of control can
cause personal injury.
• Keep hands and feet away from the cutting device at all times and
especially when switching the product on.
• Always be sure of a safe and secure operating position, whilst using the
product.
• Never use the product standing on steps or a ladder. Do not work over
should height.
• Always ensure the safety guard supplied is fitted before using the
product. Never attempt to use an incomplete product or one fitted with an
unauthorised modification.
• Check the trimming spool regularly for damage, and if damaged repair
immediately.
• Switch the product o when the trimming spool is blocked. Disconnect the
power source and remove the blockage. Inspect the spool for damage before
using the product again.
• Keep supply and extension cords away from cutting parts.
• WARNING! The cutting wire can be ejected! Risk of injury to bystandters.
• Do not cut damp or wet grass.
• Do not overload your tool.
• Do not use blade with this product!
To Next Page
Loading...
