Stihl MS 210 C

MS 210, MS 210 C, MS 230, MS 230 C, MS 250, MS 250 C
English
63
Cutting Attachments for MS 210,
MS 210 C, MS 230, MS 230 C
Recommended cutting attachments
complying with Section 5.11 of
ANSI B 175.1-2000.
Observe notes on ANSI B 175.1-2000
and definition of "low kickback chain" in
chapter on "Safety Precautions and
Working Techniques".
Rollomatic E 3/8" guide bars
3/8" P chain
Chain sprocket
Cutting Attachments for MS 250,
MS 250 C
Recommended cutting attachments
complying with Section 5.11 of
ANSI B 175.1-2000.
Observe notes on ANSI B 175.1-2000
and definition of "low kickback chain" in
chapter on "Safety Precautions and
Working Techniques".
Rollomatic E 3/8" guide bars
Rollomatic E .325" guide bars
3/8" P chain
.325" saw chain
Chain sprockets
Cutting Attachments for MS 210,
MS 210 C, MS 230, MS 230 C, MS 250,
MS 250 C
To ensure compliance with the kickback
properties required in Section 5.11 of
ANSI B 175.1-2000, only use
replacement chains that, when used
with this specific powerhead, comply
with Section 5.11 of the ANSI standard
or are classed as "low kickback" chains
according to ANSI B 175.1-2000.
Please ask your STIHL dealer for the
latest recommendations on new
bar/chain combinations developed after
publication of this instruction manual.
Reduced kickback STIHL guide bar
(with green label)
Cutting lengths: 12, 14, 16 cm (30,
35, 40 cm)
Pitch: 3/8" P (9.32 mm)
Groove width: 0.050 in (1.3 mm)
Nose sprocket: 9-tooth
Low kickback STIHL saw chains (with
green label)
Picco Micro 3 (63 PM3) Type 3636
Picco Duro (63 PD3) Type 3612
Pitch: 3/8" P (9.32 mm)
Drive link gauge: 0.050 in (1.3 mm)
6-tooth for 3/8" (spur sprocket)
Reduced kickback STIHL guide bar
(with green label)
Cutting lengths: 12, 14, 16, 18 in
(30, 35, 40, 45 cm)
Pitch: 3/8" P (9.32 mm)
Groove width: 0.050 in (1.3 mm)
Nose sprocket: 9-tooth
Reduced kickback STIHL guide bar
(with green label)
Cutting lengths: 16, 18 in (40,
45 cm)
Pitch: .325" (8.25 mm)
Groove width: 0.063 in (1.6 mm)
Nose sprocket: 11-tooth
Low kickback STIHL saw chains (with
green label)
Picco Micro 3 (63 PM3) Type 3636
Picco Duro (63 PD3) Type 3612
Pitch: 3/8" P (9.32 mm)
Drive link gauge: 0.050 in (1.3 mm)
Low kickback STIHL saw chains (with
green label)
Rapid Micro 3 (26 RM3) Type 3634
Pitch: .325" (8.25 mm)
Drive link gauge: 0.063 in (1.6 mm)
6-tooth for 3/8" (spur sprocket)
7-tooth for 0.325" (spur sprocket)