Need help?Do you have a question about the Sunbeam EM7000 and is the answer not in the manual?
General| Type | Espresso Machine |
|---|---|
| Pump Pressure | 15 bar |
| Heating System | Thermoblock |
| Material | Stainless Steel |
| Steam Wand | Yes |
| Features | Programmable, Cup warmer |
Essential safety measures for operating the Sunbeam espresso machine, covering placement, water, pressure, hot surfaces, and electrical safety.
Guidelines on intended use, placement near heat sources, cord safety, and supervision, especially concerning children.
Description of the warming plate, steam control dial, and the temperature sensing steam wand.
Details on the espresso gauge and the commercial size group head, including the sloping handle.
Information on the removable drip tray, included accessories, and single/double filter baskets.
Description of the control board, dual gauges, low water indicator, programmable panel, and the 3-litre water reservoir.
Details on unseen features like twin pumps, thermoblocks, PID technology, and power saving mode.
Explains espresso pressure, temperature stability, and the twin pump/thermoblock system.
How to interpret the espresso gauge for under-extracted, optimum, and over-extracted pours.
Explains how the milk temperature gauge helps achieve perfect milk texture.
Details the commercial specifications of the group head and the ergonomic benefits of the sloping group handle.
Description of the control board's display, buttons, and manual/programmed operation choices.
Details the 3 programmable pre-infusion settings and the function of the anti-calc water filter.
Instructions for powering on the machine and managing its automatic power saving mode.
How to perform manual espresso pours and use programmed 1 and 2 cup volumes.
Instructions for using the 2 CUP button for a programmed espresso pour.
How to activate and turn off the steam function for milk texturing.
How to activate the hot water function for dispensing hot water.
Steps to program a custom volume for the 1 CUP espresso pour.
Steps to program a custom volume for the 2 CUP espresso pour.
Procedure to revert the espresso machine to its original factory settings.
How to program the 3 pre-infusion settings: Infusion, Constant, and Progressive.
Steps to adjust the espresso thermoblock temperature in 2°C increments.
Steps to adjust the steam thermoblock temperature in 5°C increments.
How to modify the steam pump rate for wetter or dryer steam.
How to configure power saving mode inactivity times.
Procedure to revert the espresso machine to its original factory settings.
Instructions for positioning the machine, removing packaging, and filling the water reservoir.
Steps for connecting power, turning on the machine, and performing an initial water flush.
Methods for pre-heating glasses and the group handle for optimal espresso extraction.
Detailed steps for grinding, dosing, and tamping coffee grounds into the filter basket.
Guidance on extracting espresso, including infusion time, colour, resistance, and extraction evenness.
How to assess espresso quality by looking at colour change, resistance, and crema.
Steps for preparing cold milk and the jug, purging the steam wand, and positioning the steam tip.
Techniques for aerating and heating milk to create micro foam at the correct temperature.
Final steps for rolling milk, cleaning the wand, and pouring into the espresso.
Recipes for common espresso-based drinks like Espresso, Macchiato, Long Black, and Flat White.
Recipes for Caffe Latte, Caffe Mocha, Cappuccino, and Con Panna drinks.
Recommended daily cleaning steps, including drip tray and group head maintenance.
Instructions for cleaning the group head, filter baskets, and information on the group head rubber seal.
Importance of steam wand cleaning, methods to clear blockages, and general maintenance.
Detailed steps for performing the coffee thermoblock cleaning cycle.
Recommends descaling frequency and steps for preparing the machine and cleaning the shower screen.
Options for descaling solutions (tablets, liquid, vinegar) and how to activate the cycle.
Details on the pumping and rest cycles, and what happens upon completion.
Steps for refilling with clean water, running a rinse cycle, and returning the machine to standby.
Explains the terms and conditions of the 12-month repair guarantee, exclusions, and customer rights.
Provides contact details and website for Sunbeam service centres in Australia and New Zealand.
Information on how to get help, tips, and contact details for customer service.
Details on Sunbeam trademarks, copyright, and manufacturing location.
To Next Page