Sunx FX-101 - Full-Auto Teaching; PRO Mode; PRO Mode Navigation; Shift Setting Mode

,QFDVHRIIXOODXWRWHDFKLQJ
)XOODXWRWHDFKLQJLVXVHGZKHQLWLVGHVLUHGWRVHWWKHWKUHVKROGYDOXHZLWK-
RXWVWRSSLQJWKHDVVHPEO\OLQHZLWKWKHREMHFWLQWKHPRYLQJFRQGLWLRQ
Ɣ
ƒ+ROGGRZQ21NH\RU2))NH\
ƒ7KHVHWWLQJLVGRQH
ƒ³´DSSHDUVLQWKHJUHHQGLJLWDOGLVSOD\DIWHUDSSUR[VHFDQG
VWDUWVVDPSOLQJWKHLQFLGHQWOLJKWLQWHQVLW\IURPWKDWSRLQW
ƒ7KHWKUHVKROGYDOXHLVVHWZKHQ21NH\RU2))NH\LVUHOHDVHG
7HDFKLQJPRGH!
+ROGGRZQ
RU
$XWRPDWLF
$XWRPDWLF
ƒ7KHVHWWKUHVKROGYDOXHLVLQGLFDWHGRQWKHJUHHQGLJLWDOGLVSOD\
ƒ0DUJLQIRUWKHWKUHVKROGYDOXHWRWKHLQFLGHQWOLJKWLQWHQVLW\LV
LQGLFDWHGRQWKHUHGGLJLWDOGLVSOD\
:KHQWKHPDUJLQLVRUPRUH³´LVGLVSOD\HG
35202'(
8
352PRGHDSSHDUVDIWHUSUHVVLQJ02'(NH\IRUVHFLQ581PRGH
581PRGHDSSHDUV DIWHUSUHVVLQJ 02'(NH\ IRUVHFLQSURFHVVRI
VHWWLQJ+RZHYHUFKDQJHG LWHPVEHIRUH SUHVVLQJ02'( NH\IRUVHF
have been set.
Ɣ
Ɣ
(Emission halt)
<External input setting mode>
<Threshold value follow-up cycle setting mode>
(Limit teaching [+]) (Limit teaching [-]) (Full-auto teaching)
(ECO)(2-point teaching)
<Shift setting mode>
(15%)
: Select the shift amount from 0 to 80%
<PRO mode>
<RUN mode>
Press for 4 sec.
(OFF) (Under 60 sec.)
<Threshold value-storing setting mode>
(OFF) (ON)
(10 to 60 min. or less)(1 to 9 min. or less)
Automatic
<GETA function setting mode>
<Inverting digital display setting mode>
(ON)(OFF)
<ECO setting mode>
(ON)(OFF)
<Threshold value margin setting mode>
(OFF)
(Red blinks)(Green blinks)
<Setting copy mode>
: Select a target value from 0 to 2,000
(100 unit each) to correct the incident
light intensity.
(OFF) (SET)
(2,000)
(Red and Green blink)
(Incident light intensity test)
Threshold value-storing setting mode is not indicated
unless any of “ ,” “ ,” “ ” or “ ” is
set at the external input setting mode.
Alert output of external
input teaching
Alert output of external input teaching does not
operate unless any of “ ,” “ ” or
“ ” is set at the external input setting mode.
Setting item )DFWRU\VHWWLQJ 'HVFULSWLRQ
Shift setting
mode
6KLIWDPRXQWFDQEHVHOHFWHGIURPWRLQWKHOLPLW
teaching.
6HOHFWZKHQLWLVGHVLUHGWRVHWWKHSUHVHQWLQFLGHQW
light intensity as a threshold value.
([WHUQDOLQSXW
setting mode
([WHUQDOLQSXWFDQEHVHOHFWHGIURPHPLVVLRQKDOWOLPLW
teaching [+], limit teaching [-], full-auto teaching, ECO
(Note 1), 2-point teaching or emission amount test.
:KHQVHWWLQJWKHLQFLGHQWOLJKWLQWHQVLW\ WHVW ³
´
RXWSXWWXUQV21 2))HYHU\PVZKHQWKHUDWHRI
incident light intensity and threshold value is less than
half of the set shift amount IRUH[DPSOHZKHQWKHUDWH
of incident light intensity and threshold value is within
 IRU  RI VKLIW DPRXQWIRURIVKLIWDPRXQWDWH[WHUQDOLQSXW
Threshold
value-storing
setting mode
(Note 2)
Threshold value set at the limit teaching, full-auto
teaching or 2-pointWHDFKLQJE\H[WHUQDOLQSXWLVVWRUHG
When selecting Auto in the emission amount setting
mode, the set emission amount level is also stored.
Threshold value
follow-up cycle
setting mode
(Note 3)
:KHQLQFLGHQWOLJKWLQWHQVLW\H[FHHGVWKUHVKROGYDOXH
this mode can change the threshold value with each
set cycle depending on variations of the incident light
intensity. The follow-up shift amount is same as the
one set in the shift setting mode.
However, the threshold value is not stored.
GETA function
setting mode
1RWH
Variations can be reduced by correcting the present in-
FLGHQWOLJKWLQWHQVLW\LQHDFKDPSOL¿HUWRDWDUJHWYDOXH
Target value to offset incident light intensity can be
selected from 0 to 2,000 by 100 unit each.
)RUH[DPSOHLIWKHWDUJHWYDOXHLV VHWWRZKHQ
WKHLQFLGHQWOLJKWLQWHQVLW\LV WKH LQFLGHQWOLJKW
intensity becomes 2,000.
ECO setting
mode
It is possible to light up / turn off the digital display.
When ECO setting mode is ON, the display turns off in
DSSUR[VHFLQ581PRGH7ROLJKWXSWKHGLVSOD\
again, press any key for 2 sec. or more.
Inverting dig-
ital display
setting mode
'LJLWDOGLVSOD\FDQEHLQYHUWHG
Threshold
value mar-
gin setting
mode
Margin for threshold value to the present incident light
intensity can be checked. When there is no margin, it
is possible to make the digital display blink.
³
´*UHHQEOLQNV
³
´5HGEOLQNV
³
´5HGDQG*UHHQEOLQN
³
´ When conducting limit teaching or 2-point
WHDFKLQJE\H[WHUQDOLQSXWLQFDVHWKH UDWH
of reference incident light intensity and
WKUHVKROGYDOXHDIWHUWHDFKLQJLV RU
more, or in case it is less than half of the
VKLIWDPRXQWRXWSXWWXUQV21 2)) HYHU\
100ms. (Note 6)
Setting copy
mode
7KHVHWWLQJVRIWKHPDVWHUVLGHDPSOL¿HUFDQEHFRSLHG
WRWKHVODYHVLGHDPSOL¿HU
)RUGHWDLOVUHIHUWR³
6(77,1*&23<)81&7,21´
Reset mode
Returns to default settings (factory settings).
1RWHV:KHQ(&2LVVHOHFWHGDWWKHH[WHUQDOLQSXWVHWWLQJPRGHNH\RSHUDWLRQRQ
WKHPDLQERG\LVLQYDOLGGXULQJH[WHUQDOLQSXW
2)
7KLVPRGHLVQRWLQGLFDWHGXQOHVVDQ\RI³ ´³ ´³ ´RU³ ´
LVVHWDWWKHH[WHUQDOLQSXWVHWWLQJPRGH
 ,IWKHLQFLGHQWOLJKWLQWHQVLW\ EHFRPHV ³´RUOHVVWKHIROORZXS RSHUDWLRQ
stops. In that condition, threshold value [digital display (green)] blinks.
  7KLVIXQFWLRQFDQEHXVHGZKHQWKUXEHDPW\SHRUUHWURUHÀHFWLYHW\SH¿EHULV
DSSOLHGWRWKLVSURGXFW,IUHÀHFWLYHW\SH¿EHULVDSSOLHGWKHIXQFWLRQFDQQRW
be used depending on use conditions.
 ,ISUHVVLQJ02'(NH\LQ581PRGHZKHQ*(7$IXQFWLRQLVXVHGWKHLQFL-
dent light intensity before setting GETA function is displayed on the red digi-
WDOGLVSOD\IRUDSSUR[VHF
 :KHQ*(7$IXQFWLRQLVXVHGLQVDWXUDWLRQRILQFLGHQWOLJKWLQWHQVLW\RU
PRUH³
´LVLQGLFDWHGRQWKHUHGGLJLWDOGLVSOD\&RUUHFWLRQYDOXHLVXS
to 4,000.
6) 7KLVPRGHGRHVQRWRSHUDWHXQOHVVDQ\RI³ ´³ ´RU³ ´LVVHW
DWWKHH[WHUQDOLQSXWVHWWLQJPRGH
<Threshold value margin setting mode>
<RUN mode>
(YES)(NO)
<Reset mode>
(YES)(NO)
<Setting copy mode>
(READY)
: Cancellation is possible when
pressed for 2 sec. or more.
Turn the power off when copying the settings.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com