Supermicro C7C242-CB-M - Connecting Cables

Chapter 2: Installation
2-21
JTPM1
TPM/PORT80
JTPM1:
JSTBY1
5V STBY POWER
JSTBY1:
JF1
USB 3/4 (2.0)USB 10 (3.0, TypeC)
USB 8/9 (3.0)
COM1
JWD1
JPME2
AUDIO FP
JSD1:SATA DOM PWR
JSD1
JBT1:CMOS CLEAR
INTRUSION
JD1
CHASSISJL1 :
JL1
BIOS
JBT1
JCMOS
PCH SLOT4 PCI-E 3.0 x1
2-3:ME MANUFACTURING MODE
JPME2:
1-2:NORMAL
PCH SLOT5 PCI-E 3.0 x1
JD1:SPEAKER:1-4
LED1
JWD1:WATCH DOG
1-2:RST
2-3:NMI
PCH SLOT6 PCI-E 3.0 x1
JSPDIF_OUT
CPU SLOT7 PCI-E 3.0 x16
HD AUDIO
PCI-E M.2-M1
SYS_FAN2
2242
2260
MH11
2280
MH12
MH10
JI2C1
JI2C2
JI2C1/JI2C2
ON :ENABLE
OFF:DISABLE
J9702
J9701
USB2 (2.0)
(3.0)
USB7
(3.1)
USB
SYS_FAN1
5/6
LAN
JPW1
PCI-E M.2-E1
JPUSB1:USB0/1 WAKE UP
1-2 ENABLE
2-3 DISABLE
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU_FAN1
JPUSB1
LED14_CPU1
DIMM LED
CPU LED
LED14_BOOT_DEVICE
LED14_VGA1
LED14_DRAM1
VGA LED
BOOT LED
JP1
JPW2
KB/MOUSE/USB 0/1(2.0)
A
C
BIOS LICENSE
MAC CODE
BAR CODE
REV:1.02
DESIGNED IN USA
+
CA
BT1
2-3:DEBUG MODE
J9701/J9702
1-2:NORMAL
2-3:CLEAR CMOS JCMOS: 1-2:NORMAL
I-SATA5
I-SATA4
I-SATA3
I-SATA2
I-SATA1
I-SATA0
PWR
ON
RST
X
OH/FF
NIC
X
1
HDD
LED
LED
PWR
WIFI+BT (for C7242-CB-MW only)
2-8 Connecting Cables
This section provides brief descriptions and pinout denitions for onboard
headers and connectors. Be sure to use the correct cable for each header
or connector.
A. 24-Pin ATX Main PWR
B. 8-Pin PWR
ATX Power 24-pin Connector
Pin Definitions (JPW1)
Pin# Denition Pin # Denition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
(Required)
12V 8-pin Power
Connector Pin
Definitions
Pins Denition
1-4 Ground
5-8 +12V
ATX Main PWR & CPU PWR
Connectors (JPW1 & JPW2)
The 24-pin main power connector (JPW1)
is used to provide power to the moth-
erboard. The 8-pin CPU PWR connector
(JPW2) is also required for the processor.
These power connectors meet the SSI
EPS 12V specication. Refer to the tables
on the right and below for pin denitions.
A
B