Chapter 2: Installation
2-29
JTPM1
JSTBY1
5V STBY POWER
JSTBY1:
JF1
USB 3/4 (2.0)USB 10 (3.0, TypeC)
USB 8/9 (3.0)
COM1
JWD1
JPME2
AUDIO FP
JSD1:SATA DOM PWR
JSD1
JBT1:CMOS CLEAR
INTRUSION
JD1
CHASSISJL1 :
JL1
BIOS
JBT1
JCMOS
PCH SLOT4 PCI-E 3.0 x1
2-3:ME MANUFACTURING MODE
JPME2:
1-2:NORMAL
PCH SLOT5 PCI-E 3.0 x1
JD1:SPEAKER:1-4
LED1
JWD1:WATCH DOG
1-2:RST
2-3:NMI
PCH SLOT6 PCI-E 3.0 x1
JSPDIF_OUT
CPU SLOT7 PCI-E 3.0 x16
HD AUDIO
PCI-E M.2-M1
SYS_FAN2
2242
2260
MH11
2280
MH12
MH10
JI2C1
JI2C2
JI2C1/JI2C2
ON :ENABLE
OFF:DISABLE
J9702
J9701
USB2 (2.0)
(3.0)
USB7
(3.1)
USB
SYS_FAN1
5/6
LAN
JPW1
PCI-E M.2-E1
JPUSB1:USB0/1 WAKE UP
1-2 ENABLE
2-3 DISABLE
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU_FAN1
JPUSB1
LED14_CPU1
DIMM LED
CPU LED
LED14_BOOT_DEVICE
LED14_VGA1
LED14_DRAM1
VGA LED
BOOT LED
JP1
JPW2
KB/MOUSE/USB 0/1(2.0)
A
C
BIOS LICENSE
MAC CODE
BAR CODE
REV:1.02
DESIGNED IN USA
+
CA
BT1
2-3:DEBUG MODE
J9701/J9702
1-2:NORMAL
2-3:CLEAR CMOS
JCMOS:
1-2:NORMAL
I-SATA5
I-SATA4
I-SATA3
I-SATA2
I-SATA1
I-SATA0
PWR
ON
RST
X
OH/FF
NIC
X
1
HDD
LED
LED
PWR
WIFI+BT (for C7242-CB-MW only)
JBT1 & JCMOS
JBT1 is used to clear the saved system setup conguration stored in the
CMOS chip. To clear the contents of the CMOS usng JBT1, short the two
pads of JBT1 with a metallic conductor such as a athead screwdriver.
JCMOS works similarly to JBT1. Close pins 2 and 3 of JCMOS to clear
CMOS. This will erase all user settings and revert everything to their
factory defaults.
A. JBT1
B. JCMOS
C. JWD1
Watch Dog
Jumper Settings
Jumper Setting Denition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled
Watch Dog Timer Enable/Disable
Watch Dog (JWD1) is a system monitor
that can reboot the system when a soft-
ware application hangs. Close pins 1 and
2 to reset the system if an application
hangs. Close pins 2 and 3 to generate a
non-maskable interrupt signal for the ap-
plication that hangs. Refer to the table on
the right for jumper settings.
A
B
C
To Next Page
Loading...
