Supermicro SUPERSERVER 5019S-MT - Page 43

Chapter 6: BIOS
7776
SuperServer 5019S-MT User's Manual
Serial Port 1
Select Enabled to enable the selected onboard serial port. The options are Disabled and
Enabled.
Logical Device Settings
This item displays the status of a serial part specied by the user.
Serial Port 1 Change Settings
This feature species the base I/O port address and the Interrupt Request address of a serial
port specied by the user. Select Auto to allow the BIOS to automatically assign the base
I/O and IRQ address. The options are Auto, (IO=3F8h; IRQ=4;), (IO=3F8h; IRQ=3, 4, 5, 6,
7, 9, 10, 11, 12;), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;), (IO=3E8h; IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12;), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;).
Serial Port 2
SerialPort2Conguration
This submenu allows the user the congure settings of Serial Port 1.
Serial Port 2
Select Enabled to enable the selected onboard serial port. The options are Disabled and
Enabled.
Logical Device Settings
This item displays the status of a serial part specied by the user.
Serial Port 2 Change Settings
This feature species the base I/O port address and the Interrupt Request address of a serial
port specied by the user. Select Auto to allow the BIOS to automatically assign the base
I/O and IRQ address. The options are Auto, (IO=2F8h; IRQ=3;), (IO=3F8h; IRQ=3, 4, 5, 6,
7, 9, 10, 11, 12;), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;), (IO=3E8h; IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12;), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;).
Serial Port 2 Attribute (Available for Serial Port 2 only)
Select SOL to use COM Port 2 as a Serial Over LAN (SOL) port for console redirection. The
options are SOL and COM.
Intel Server Platform Services
The following Intel Server Platform Services information will display:
• ME BIOS Interface Version
• SPS Version
Onboard 10G LAN Option ROM Type
Use this item to select the Onboard 10G LAN Option ROM type. The options are Disabled,
Legacy, and EFI.
Onboard SAS Option ROM
Select Enabled to enable SAS Option ROM support to boot the computer using a SAS device
specied by the user. The options are Disabled, Legacy, and EFI.
Onboard Video Option ROM
Use this item to select the Onboard Video Option ROM type. The options are Disabled,
Legacy, and EFI.
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unied Extensible
Firmware Interface) for network stack support. The options are Disabled and Enabled.
IPv4 PXE Support
Select Enabled to enable IPv4 PXE boot support. The options are Disabled and Enabled.
IPv6 PXE Support
Select Enabled to enable IPv6 PXE boot support. The options are Disabled and Enabled.
PXE boot wait time
Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press
"+" or "-" on your keyboard to change the value. The default setting is 0.
Media detect count
Use this option to specify the number of times media will be checked. Press "+" or "-" on your
keyboard to change the value. The default setting is 1.
SuperIOConguration
The following Super IO information will display:
• Super IO Chip AST2400
SuperIOChipLogicalDevice(s)Conguration
Serial Port 1
SerialPort1Conguration
This submenu allows the user the congure settings of Serial Port 1.