Supermicro X8DTN+-F-LR - Internal Speaker; Power Led;Speaker

3-28
X8DTN+-F/X8DTN+-F-LR User's Manual
JBAT1
LE2
JPI2C1
JD1
JPP0
JPP1
JP7
JP5
JWOR1
JI2C1
JI2C2
LE1
LEM1
FAN4
FAN3
FAN2
FAN7
FAN5
FAN6
SP1
JF1
JWD
JPL1
JPB
JPW2
JPW3
JTPM1
SW1
JWF1
JPW1
USB4/5
USB6/7
USB10
UID
IPMI_LAN
USB2/3
ALWAYS POPULATE DIMMxA FIRST
P1 DIMM3B
P1 DIMM3A
P1 DIMM2C
P1 DIMM2B
P1 DIMM2A
P1 DIMM3C
P1 DIMM1C
P1 DIMM1B
P1 DIMM1A
P2 DIMM3A
P2 DIMM3B
P2 DIMM3C
P2 DIMM2A
P2 DIMM2B
P2 DIMM2C
P2 DIMM1A
P2 DIMM1B
FAN8/CPU1
CPU2
I-SATA5
I-SATA4
I-SATA3
I-SATA2
I-SATA1
USB8
Slot6 PCI-E 2.0 x8 (In x16 Slot)
Slot5 PCI-E x4 (In x8 Slot)
Slot4 PCI-E 2.0 x8 (In x16 Slot)
Slot3 PCI-E 2.0 x4 (In x8 Slot)
Slot2 PCI-E 2.0 x4 (In x8 Slot)
LAN2
VGA (Bottom)
COM1 (Top)
KB/MOUSE
P2 DIMM1C
I-SATA0
PWR I2C
FAN7/CPU2
CPU1
USB0/1
T-SGPIO2
LAN1
Slot0 PCI-U
COM2
PHY
IPMB
JL1
T-SGPIO1
Intel ICH10R
South Bridge
BIOS
Intel IOH36
FP CTRL
JPG1
ALWAYS POPULATE DIMMxA FIRST
X8DTN+-F
Rev. 2.00
LAN CTRL
BMC CTRL
FAN1
JBT1
B
A
A. Internal Speaker (Buzzer)
B. PWR LED/Speaker
Power LED/Speaker
On the JD1 header, pins 1-3 are used
for power LED indication, and pins 4-7
are for the speaker. See the tables
on the right for pin defi nitions. Please
note that the speaker connector pins
(4-7) are for use with an external
speaker. If you wish to use the on-
board speaker, you should close pins
6-7 with a jumper.
Speaker Connector
Pin Settings
Pin Setting Defi nition
Pins 4-7 External Speaker
Pins 6-7 Internal Speaker
Internal Speaker
The Internal Speaker, located at SP1,
can be used to provide audible indica-
tions for various beep codes. See the
table on the right for pin defi nitions.
Refer to the layout below for the loca-
tions of the Internal Buzzer (SP1).
Internal Buzzer (SP1)
Pin Defi nition
Pin# Defi nitions
Pin 1 Pos. (+) Beep In
Pin 2 Neg. (-) Alarm
Speaker
PWR LED Connector
Pin Defi nitions
Pin Setting Defi nition
Pin 1 Anode (+)
Pin2 Cathode (-)
Pin3 NA