EasyManua.ls Logo

Supermicro X8DTN+-F-LR - CMOS Clear; Watch Dog Enable;Disable

Supermicro X8DTN+-F-LR
107 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
3-34
X8DTN+-F/X8DTN+-F-LR User's Manual
JBAT1
LE2
JPI2C1
JD1
JPP0
JPP1
JP7
JP5
JWOR1
JI2C1
JI2C2
LE1
LEM1
FAN4
FAN3
FAN2
FAN7
FAN5
FAN6
SP1
JF1
JWD
JPL1
JPB
JPW2
JPW3
JTPM1
SW1
JWF1
JPW1
USB4/5
USB6/7
USB10
UID
IPMI_LAN
USB2/3
ALWAYS POPULATE DIMMxA FIRST
P1 DIMM3B
P1 DIMM3A
P1 DIMM2C
P1 DIMM2B
P1 DIMM2A
P1 DIMM3C
P1 DIMM1C
P1 DIMM1B
P1 DIMM1A
P2 DIMM3A
P2 DIMM3B
P2 DIMM3C
P2 DIMM2A
P2 DIMM2B
P2 DIMM2C
P2 DIMM1A
P2 DIMM1B
FAN8/CPU1
CPU2
I-SATA5
I-SATA4
I-SATA3
I-SATA2
I-SATA1
USB8
Slot6 PCI-E 2.0 x8 (In x16 Slot)
Slot5 PCI-E x4 (In x8 Slot)
Slot4 PCI-E 2.0 x8 (In x16 Slot)
Slot3 PCI-E 2.0 x4 (In x8 Slot)
Slot2 PCI-E 2.0 x4 (In x8 Slot)
LAN2
VGA (Bottom)
COM1 (Top)
KB/MOUSE
P2 DIMM1C
I-SATA0
PWR I2C
FAN7/CPU2
CPU1
USB0/1
T-SGPIO2
LAN1
Slot0 PCI-U
COM2
PHY
IPMB
JL1
T-SGPIO1
Intel ICH10R
South Bridge
BIOS
Intel IOH36
FP CTRL
JPG1
ALWAYS POPULATE DIMMxA FIRST
X8DTN+-F
Rev. 2.00
LAN CTRL
BMC CTRL
FAN1
JBT1
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact
pads to prevent the accidental clearing of CMOS. To clear CMOS, use a metal
object such as a small screwdriver to touch both pads at the same time to short
the connection. Always remove the AC power cord from the system before clear-
ing CMOS.
Note 1. For an ATX power supply, you must completely shut down the
system, remove the AC power cord and then short JBT1 to clear CMOS.
Note 2. Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3. Clearing CMOS will also clear any passwords.
A
B
A. Clear CMOS
B. Watch Dog Enable
Watch Dog Enable/Disable
Watch Dog (JWD) is a system monitor that
can reboot the system when a software ap-
plication hangs. Close Pins 1-2 to reset the
system if an application hangs. Close Pins
2-3 to generate a non-maskable interrupt
signal for the application that hangs. See the
table on the right for jumper settings. Watch
Dog must also be enabled in the BIOS.
Watch Dog
Jumper Settings
Jumper Setting De nition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled

Table of Contents

Related product manuals