Svantek SVAN 958 - Page 4

SVAN 958 USER MANUAL _
ii
5.4 Triggering mode and parameters selection - TRIGGER SETUP 5-12
5.4.1 Switching the triggering on and off - TRIGGER 5-12
5.4.2 Selection of the triggering signal - SOURCE 5-13
5.4.3 Selection of channel for triggering condition - CHANNEL 5-14
5.4.4 Setting the level of the triggering signal - LEVEL 5-14
5.4.5 Setting the speed of the triggering signal changes - GRADIENT 5-15
5.4.6 Setting the start of time-triggered measurement - RTC START 5-15
5.4.7 Setting the step for repetition of time-triggered measurement - RTC STEP 5-15
5.5 Setting parameters of auxiliary functions - AUXILIARY SETUP 5-16
5.5.1 Setting the parameters of RPM function - RPM SETUP 5-16
5.5.1.1 Enabling the RPM measurement - ENABLED 5-16
5.5.1.2 Selecting the number of pulses / rotations - PULSES / ROTATION 5-17
5.5.1.3 Selecting the unit of RPM measurement - UNIT 5-17
5.5.1.4 Activation of logger for RPM measurements - LOGGER 5-17
5.5.2 Setting the parameters of attenuation measurements - “SEAT” SETUP 5-18
5.5.2.1 Enabling the attenuation measurements - ENABLED 5-18
5.5.2.2 Selection of the seat channel for attenuation measurements -
SEAT CHANNEL 5-19
5.5.2.3 Selection of the base channel for attenuation measurements -
BASE CHANNEL 5-19
5.5.3 Settings for vector calculations - VECTOR SETUP 5-19
5.5.4 Setting the parameters for dose measurements - HAV/WBV DOSE SETUP 5-21
5.5.4.1 Enabling HAV/WBV settings - ENABLED 5-21
5.5.4.2 Setting the time of exposure - EXPOSURE TIME 5-22
5.5.4.3 Selection of channels for HAV/WBV DOSE calculation - X AXIS, Y AXIS,
Z AXIS 5-22
5.5.4.4 Standards selection for HAV/WBV dose calculation - STANDARDS 5-22
5.6 Selection of parameters for alarm triggering - ALARM SETUP 5-23
5.7 Selection of dosimeter parameters - DOSIMETER SETUP 5-26
5.7.1 Setting the exposure time - EXPOSURE TIME 5-26
5.7.2 Setting criterion sound level - CRITERION LEVEL 5-26
5.7.3 Setting threshold level - THRESHOLD LEVEL 5-27
5.7.4 Setting exchange rate - EXCHANGE RATE 5-27
5.8 Selection of FFT analysis parameters - FFT SETUP 5-27
5.8.1 Enabling the FFT analysis - ENABLED 5-28
5.8.2 Selecting the weighting filter during the FFT analysis - FILTER 5-28
5.8.3 Selecting the analysis band of the signal - BAND 5-28
5.8.4 Selecting the time window for the FFT analysis - WINDOW 5-29
5.8.5 Selecting the number of the lines in FFT analysis - LINES 5-29
5.8.6 Enabling the FFT spectra time-history logging - LOGGER 5-30
5.9 Selection of 1/1 and 1/3 octave spectrum parameters - 1/1 OCTAVE SETUP and
1/3 OCTAVE SETUP 5-30
5.9.1 Enabling 1/1 OCTAVE or 1/3 OCTAVE spectrum settings - ENABLED 5-30
5.9.2 Selecting the weighting filter during 1/1 OCTAVE or 1/3 OCTAVE analysis - FILTER5-31
5.9.3 Selecting the band during 1/1 OCTAVE or 1/3 OCTAVE analysis - BAND 5-31
5.9.4 Activation of logger for 1/1 OCTAVE or 1/3 OCTAVE analysis results - LOGGER 5-32