SVAN 958 USER MANUAL
vii
CHANNEL 4 SETUP, MICROPHONE CORRECTION text selected .....................................................................5-9
MICROPHONE CORRECTION window, DIFFUSE FIELD selection and OUTDOOR selection..........................5-9
LOGGER SETUP option selected and available LOGGER MODES .....................................................................5-10
LOGGER SETUP windows (VM) with the selection of the results to be saved or saved in a logger’s file.............5-10
LOGGER SETUP windows (SM) with the selection of the results to be saved in a logger’s file............................5-10
AUXILIARY LOGGER window with the selection of VECTOR and RPM result to be saved in a logger’s file ...5-11
LOGGER SETUP window, SAMPLING RATE selection......................................................................................5-11
LOGGER SETUP window, RPM selection .............................................................................................................5-11
LOGGER SETUP window, CHANNEL 4 deactivation ..........................................................................................5-12
LOGGER VIEW window with the file with time-domain signal recorded and message on the display after
attempt to open the file .................................................................................................................................5-12
INPUT window with TRIGGER SETUP text selected ............................................................................................5-12
TRIGGER SETUP window with TRIGGER mode selection...................................................................................5-12
Displays during the measurements while the triggering condition is not fulfilled....................................................5-13
Displays during the measurements while the triggering condition is not fulfilled....................................................5-13
TRIGGER SETUP windows with SOURCE selection ............................................................................................5-14
TRIGGER SETUP windows with CHANNEL selection.........................................................................................5-14
TRIGGER SETUP windows with LEVEL selection in VM....................................................................................5-14
TRIGGER SETUP windows with GRADIENT selection (1 dB/ms and 10 dB/ms step up) ...................................5-15
TRIGGER SETUP windows with RTC START selection with 1-second step........................................................5-15
TRIGGER SETUP windows with RTC START selection with 1-minute step ........................................................5-15
TRIGGER SETUP windows, RTC STEP selection with 1-second step ..................................................................5-15
TRIGGER SETUP windows, RTC STEP selection with 1-minute step ..................................................................5-16
INPUT list with AUXILIARY SETUP text highlighted (displayed inversely)........................................................5-16
AUXILIARY SETUP windows with all available positions....................................................................................5-16
RPM SETUP window with enabling RPM function ................................................................................................5-16
RPM SETUP window with PULSES/ROTATION selection with 1-unit step.........................................................5-17
RPM SETUP window with PULSES/ROTATION selection with 10-units step .....................................................5-17
RPM SETUP window; the UNIT selection..............................................................................................................5-17
RPM SETUP windows with LOGGER activation ...................................................................................................5-18
AUXILIARY SETUP window with “SEAT” SETUP text highlighted ...................................................................5-18
Selection of SEAT results presentation....................................................................................................................5-18
“SEAT” SETUP windows with the enabling of the function ...................................................................................5-19
“SEAT” SETUP windows with SEAT CHANNEL selection..................................................................................5-19
“SEAT” SETUP windows with BASE CHANNEL selection..................................................................................5-19
AUXILIARY SETUP window with VECTOR SETUP text highlighted.................................................................5-19
VECTOR SETUP windows with the coefficient selection with 1-unit step.............................................................5-20
VECTOR SETUP windows with the coefficient selection with 10-units step .........................................................5-20
VECTOR SETUP windows with the selection of results from channels for vector calculation...............................5-20
Display in the starting measurements when user selects incorrect filters for HAV/WBV calculations....................5-20
AUXILIARY SETUP window with HAV/WBV DOSE SETUP text selected........................................................5-21
Display after starting measurements when user selected incorrect filters for HAV/WBV DOSE calculations........5-21
HAV/WBV DOSE windows with the enabling of the option...................................................................................5-22
HAV/WBV DOSE windows with EXPOSURE TIME selection with 30-minutes step...........................................5-22
HAV/WBV DOSE windows with EXPOSURE TIME selection with 1-minute step ..............................................5-22
HAV/WBV DOSE windows with the selection of the channel for X AXIS ............................................................5-22
HAV/WBV DOSE windows with STANDARDS text highlighted..........................................................................5-23
STANDARDS windows with STANDARD selection.............................................................................................5-23
INPUT list, ALARM SETUP text highlighted.........................................................................................................5-23
ALARM SETUP windows, CHANNEL 2 or VECTOR selection...........................................................................5-24
Vibration channel opened in LM (a), sound channel opened in LM (b) VECTOR ALARM window opened in
LM (c) vibration channel opened in 1/1 OCTAVE (d) and 1/3 OCTAVE (e) analysis mode ......................5-24
Setting ALARM conditions, TRIGGER mode selection..........................................................................................5-24
Setting ALARM conditions, INTEGRATION period selection ..............................................................................5-24
Source selection in the case of vibration mode ........................................................................................................5-25
Source selection in the case of sound mode .............................................................................................................5-25
SOURCE selection for 1/3 OCTAVE option...........................................................................................................5-25
LEVEL selection with 0.1dB step and with 1dB step in the vibration channel/mode..............................................5-25
LEVEL selection with 0.1dB step and with 1dB step in sound channel/mode.........................................................5-25
To Next Page
Loading...
