SWF E-Series User Manual

71 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

MMMMEE--111100110033

USER

’’

S MANUAL

SSuunnSSttaarr CCOO..,, LLTTDD..

TWO-HEAD AUTOMATIC

EMBROIDERY MACHINE

FOUR-HEAD AUTOMATIC

EMBROIDERY MACHINE

SIX-HEAD AUTOMATIC

EMBROIDERY MACHINE

EIGHT-HEAD AUTOMATIC

EMBROIDERY MACHINE

SIX-HEAD AUTOMATIC

EMBROIDERY MACHINE

(Compact Type)

SWF/E-Series

Table of Contents

Other manuals for SWF E-Series

Questions and Answers:

B
brennanpaulAug 21, 2025
How to resolve thread breaks on my SWF E-Series?
- R
  Randy FernandezAug 21, 2025
  Thread breaks on your SWF Sewing Machine can be caused by several factors: the stitch being too small or dense for the thread (re-punch design tape or re-punch after checking design), frequent thread breaks in the same spot (correct the stitches on the operation box), inadequate needle size for the thread (change needle), needle damage (bent, dent, worn) (change needle), incorrect needle installation (height, direction, etc.) (re-install needle), or a dirty needle (adhesive, etc.) (clean or change needle and hook).
C
Curtis ScottAug 22, 2025
Why is my SWF E-Series Sewing Machine showing operation failure?
- L
  Leslie OchoaAug 23, 2025
  Operation failure in your SWF Sewing Machine can be due to several reasons: loose belt tension or belt damage (adjust belt tension or change the belt), power failure or short-circuit of fuse (check and change the fuse in the main shaft motor), or failure to sense signals for needle position or 1 rotation (run manual color change and check if signal lamps blink at the correct needle position, adjust the half-turn film, address the cause and press RESET, then check if the lamp turns green). Also, check the connection of the START switch.
E
ericnewmanAug 25, 2025
What to do if my SWF E-Series has bad color change?
- J
  Joshua WhiteAug 25, 2025
  If your SWF Sewing Machine has a bad color change, it could be due to several factors. Refer to the user’s manual, run a manual color change, and check if the signal lamps (needle set lamp & needle position lamp) blink at the correct needle position. Adjust the half-turn film. Other potential causes include an incorrect position of the needle bar (set it to the correct position), an incorrect position of the take-up lever (adjust so take-up lever is in line with other levers in stop position, upper shaft angle: 100°), or a bad connection (change fuse F3 in the joint board or check the connection).
T
Tim MoralesAug 27, 2025
What causes bad stitch quality on SWF E-Series Sewing Machine?
- G
  griffithlisaAug 28, 2025
  Bad stitch quality on your SWF Sewing Machine can stem from several causes: bad tape (correct tape), inadequate tension on the X-Y belt (adjust tension), foreign substance in the X-Y rail (clean the rail), failure of the X/Y driver board (change circuit board), or a heavy load on the frame (reduce speed of main shaft).
A
Alyssa FloresAug 29, 2025
What causes poor stitch tension on my SWF E-Series Sewing Machine?
- M
  madison91Aug 29, 2025
  Poor stitch tension in your SWF Sewing Machine can be attributed to: weak upper thread tension (adjust tension), uneven upper thread tension due to foreign substances (clean main and sub tension adjusters in the thread tension adjusting plate), weak lower thread tension (adjust tension), uneven lower thread tension (clean bobbin case and check tension on bobbin spring), thread thickness (change to quality thread), poor timing of needle and hook (adjust timing), or insufficient oil in hook (oil the raceway of hook).
A
Arthur CherryAug 31, 2025
What causes needle breaks on my SWF Sewing Machine?
- D
  Danielle ZimmermanAug 31, 2025
  Needle breaks in your SWF Sewing Machine can occur due to: a bent needle (change needle), a bad quality needle (space the needle and the hook point), the tip of the needle being worn or bent (correct the installation), the needle touching the hook point (check if needle plate is unscrewed), incorrect installation of the needle (adjust the position of the needle bar), or the needle touching the needle hole on the plate.
R
Ronnie StoutSep 1, 2025
What causes puckering on my SWF Sewing Machine?
- J
  Joseph FosterSep 1, 2025
  Puckering on your SWF Sewing Machine can be caused by excessive thread tension (adjust tension), excessive pressure of the presser foot (change presser foot spring), needle failure such as a worn out or damaged needle tip (change needle), the needle being too large for the thread (use adequate size of needle), or the needle hole being too large for the needle.
S
skingSep 3, 2025
What causes incorrect stop position on SWF E-Series?
- J
  Jonathan FrancisSep 3, 2025
  An incorrect stop position on your SWF Sewing Machine can be due to loose tension on the main driver belt (adjust belt tension), or an incorrect position of the encoder or a bad encoder (adjust encoder position or change encoder).

SWF E-Series Specifications

General

Type	Embroidery Machine
Needle Threader	Automatic
Maximum Speed	1, 000 SPM
Data Input	USB
Power Supply	220V, 50/60Hz
Speed Control	Adjustable
Heads	Single head

Related product manuals

SWF SWF/E-T601C

SWF SWF/E-T901C

SWF SWF/E-T1201C

SWF SWF/E-T1501C

SWF Dual Function E Series

Preview: SWF MA-6

Preview: SWF MAN-12

SWF DM-WD920-55