To Next PageTo Next PageWhy is there not enough flow from my Symmons Bathroom Fixtures faucet?
If you're experiencing reduced water flow from your Symmons Bathroom Fixtures faucet, the in-line screen might be clogged. To resolve this, disassemble the supply to the faucet and remove the in-line screen (I) located in the inlet. Rinse the screen with water or a deliming agent before reassembling the faucet supply.
What to do if my Symmons Bathroom Fixtures faucet drips?
If your Symmons Bathroom Fixtures faucet is dripping, it could be due to a worn seat washer or foreign matter trapped between the washer and seat surface. Disassemble the cartridge (F), remove the piston (F6), remove the screw (F7), and clean the seat washer (F8). Also, check the control rod pin (F9) for any burrs before reassembling.
How to fix a Symmons Bathroom Fixtures faucet that runs constantly?
If your Symmons Bathroom Fixtures faucet runs constantly, the seat washer might not be closing properly, or the seat washer or seat surface is worn. Remove the piston (F6) and spring (F12). Check for burrs on the pin (F9) and inspect the spring. You may need to replace both the piston and the spring. If there's excessive wear, consider replacing the entire cartridge (F).
Why is my Symmons Bathroom Fixtures faucet bleeding between hot and cold, not holding consistent temperature?
If your Symmons Bathroom Fixtures faucet is bleeding between hot and cold, and not holding a consistent temperature, the integral checks in the mechanical mixing valve might not be operating correctly. Try cleaning and replacing the integral checks (T) in the mechanical mixing valve (U).
What to do if my Symmons Bathroom Fixtures faucet leaks under the handle?
If water leaks from under the handle of your Symmons Bathroom Fixtures faucet, the stem washers are likely worn. Remove the cartridge (F) and replace the housing o-rings (E1). If the leak continues, replace the control spindle kit (F1).
Why is my Symmons Bathroom Fixtures handle loose?
If the handle on your Symmons Bathroom Fixtures is loose, it's likely that the set screw has loosened. Simply tighten the set screw (B).
How to fix Symmons Bathroom Fixtures faucet leaks on or under the counter?
If your Symmons Bathroom Fixtures faucet leaks on or under the counter, the supply housing o-rings are probably worn. Replace the housing o-rings (E1).
How to adjust the run time on my Symmons Bathroom Fixtures faucet?
If your Symmons Bathroom Fixtures faucet runs too long or too short, the cycle timing washers may need adjustment. Remove the handle (A), then add cycle timing washers (C) to the stem to shorten the time or remove washers to lengthen the time.
What causes spotting on the finish of my Symmons Bathroom Fixtures?
Spotting on the finish of your Symmons Bathroom Fixtures can be caused by elements in the water supply. Clean the finished trim area with a soft cloth, using mild soap and water or a non-abrasive cleaner. Quickly rinse with water afterward.
General| Brand | Symmons |
|---|---|
| Model | SCOT SLS-7000 Series |
| Category | Plumbing Product |
| Language | English |
Lists available model numbers for the metering lavatory faucet.
Details available modifications and optional suffixes for the faucet model.
Provides key product specifications like water flow, vandal resistance, and construction.
Presents a diagram with labeled dimensions and a table of measurements.
Lists industry standards and certifications the faucet meets.
Outlines warranty terms for residential and commercial installations.
Illustrates the faucet assembly with labeled components for easy identification.
Provides a table of faucet components with corresponding part numbers.
Lists necessary tools and materials for installing the faucet.
Step-by-step guide for mounting the faucet body and escutcheon.
Instructions for connecting water supply lines to the faucet.
Guidance on adjusting faucet cycle time and water temperature.
Steps for disassembling, inspecting, and reassembling faucet components.
Specific instructions for installing the faucet with a MAXLINE thermostatic mixing valve.
Identifies common faucet problems, their causes, and recommended solutions.
