EasyManua.ls Logo

Symmons Temptrol 261XBODY - User Manual

Default Icon
12 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
ZV-3247 REV B
Temptrol
®
Pressure Balancing Valve
Installation Instructions
262BODY
(4 PORT)
262XBODY
(4 PORT, SERVICE STOPS)
261XBODY
(3 PORT, SERVICE STOPS)
IMPORTANT / FOR INSTALLER
WARNING:
As the installer of this valve, you must first carefully read and understand the material covered in this manual before
installing and adjusting this valve per instructions. Failure to do so may compromise the installation, operation and/or
serviceability of this valve.
Do not install positive shut-o devices on the outlet of this valve, or devices that do not allow the valve to flow at
least 1.5 GPM at 45 psi inlet pressure. Exception: If a self-closing or slow-closing valve is installed on the outlet, the
supplies of the valve must be equipped with checks to eliminate hot to cold bypass in the event the valve’s handle is
not turned o after use.
When installing this valve, failure to adjust limit stop screw properly may result in serious scalding.
COMPLIANCE
-ASME A112.18.1/CSA B125.1
-ASSE 1016
-Buy American Act Compliant
LIFETIME LIMITED WARRANTY
All warranty claims MUST be pre-approved by Symmons.
All parts and finishes of the Symmons products are
warranted to the original consumer purchaser to be free
from manufacturing defects in material and workmanship
for 5 years Non-Residential or Commercial Applications.
Symmons warrants to the original consumer purchaser/
end-user that any Symmons product will be free of
defects in material and workmanship during normal
domestic use for the life of your home.
Symmons recommends using a professional plumber
for all installation and repair. During the warranty
period, Symmons at its sole option, will provide
replacement part(s) or product (or, if no longer available,
a comparable product) to replace those which have
proven defective in materials or workmanship under
normal installation, use and service, FREE OF CHARGE
for the time period of 5 years from the date of purchase.
(BATTERIES NOT INCLUDED)
This warranty is extensive in that it covers replacement of
all defective parts and even finish, but these are the only
two things that are covered. Damage due to installation
error, product abuse, product misuse, or use of cleaners
containing abrasives, alcohols, or other organic solvents,
whether performed by a contractor, Service Company
or yourself are excluded from this warranty. Symmons
will not be responsible for labor charges and/or damage
incurred in installation or repair or replacement, nor for
any indirect, incidental or consequential damages, losses,
injury or costs of any nature relating to the bathing
products. Except provided by law, this warranty is in
lieu of and excluded all other warranties, conditions and
guarantees, whether expressed or otherwise, including
without restriction those of merchantability or of fitness
for use.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above
limitation of exclusion may not apply to you. This
warranty gives you specific legal rights, and you also may
have other rights which vary from state to state. This
warranty is not transferable. This warranty does not cover
damage or defects relating to misuse, abuse, negligence,
normal wear and tear, accident, acts of God, repairs or
alterations not authorized in writing by Symmons, or
improper installation, storage or handling.
The above mentioned warranty information includes each
product that falls under the following: Symmons Bathing
Products Warranty- Non-Residential or Commercial
Applications; Symmons Non-Electronic Lifetime
Faucet and Finish Limited Warranty Non-Residential or
Commercial Applications; Symmons Electronic Faucet
Limited Warranty - Non-Residential, Commercial and
Residential Applications; Symmons Bathing Products
Warranty- Residential Application Symmons Non-
Electronic Lifetime Faucet and Finish Limited Warranty
Residential Application
If you have any questions regarding technical support,
installation or concerns regarding our warranty plan,
please email us at GetHelp@symmons.com or call us at:
1-800-796-6667.
RTS-076
(BRACKET)

Questions and Answers

  • B
    briggspamelaAug 5, 2025
    What to do if Symmons Control Unit temperature varies without moving handle?
    • T
      Theresa LucasAug 5, 2025
      If the temperature varies without you adjusting the handle, it's likely that the pressure-balancing piston inside the spindle assembly is blocked by foreign particles. To resolve this, open the valve halfway, take off the handle, and gently tap the spindle using a plastic hammer. Inspect the water pressure balancing piston within the control spindle, referring to the service instructions for guidance. Consider replacing the TA-10 flow control spindle.
  • H
    harry56Aug 9, 2025
    What to do if Symmons Temptrol 261XBODY Control Unit delivers sufficient quantity of cold, but little hot, or the reverse?
    • A
      Andrew KingAug 9, 2025
      If your Symmons Control Unit delivers plenty of cold water but very little hot water (or vice versa), it's likely that the pressure-balancing piston in the spindle assembly is being restricted by foreign matter. To fix this, open the valve halfway, remove the handle, and tap the spindle with a plastic hammer. Also, check the water pressure balancing piston in the control spindle, and refer to the service instructions. Replacing the TA-10 flow control spindle may also resolve the issue.
  • N
    Nicholas BennettAug 13, 2025
    What to do if the Symmons Control Unit temperature control handle is turned from cold to hot and volume from spout or head is not constant?
    • K
      Kelsey AllenAug 13, 2025
      If you're experiencing inconsistent water volume from the spout or showerhead while adjusting the temperature on your Symmons Control Unit, it's probably due to the pressure-balancing piston in the spindle assembly being blocked by foreign particles. Try opening the valve halfway, removing the handle, and gently tapping the spindle with a plastic hammer. Inspect the water pressure balancing piston in the control spindle, consulting the service instructions. Replacing the TA-10 flow control spindle might be necessary.
  • T
    terrimartinezAug 17, 2025
    Why does Symmons Temptrol 261XBODY deliver hot water when initially opened, then turns colder?
    • A
      adelacruzAug 18, 2025
      If your Symmons Control Unit initially dispenses hot water that gradually turns colder as you rotate the handle towards the hot position, the valve is likely piped incorrectly. The hot supply is connected to the valve’s cold inlet, and the cold supply to the hot inlet. If the piping is accessible, correct the connections to the valve. If not, order a T-108 reverse seat and tool kit. Older installations might also need a replacement of the TA-4 hot/cold seat repair kit.
  • J
    Jennifer McgeeAug 22, 2025
    What to do if Symmons Temptrol 261XBODY Control Unit valve leaks when shut off?
    • R
      ramirezjonathanAug 22, 2025
      If your Symmons Control Unit valve is leaking after being shut off, the hot and cold washers are likely worn, or there's foreign matter (like dirt or chips) trapped between the washers and seat surfaces. Replace the washers using a TA-9 washer repair kit. Also, replace the hot and cold seats using a TA-4 hot/cold seat repair kit.
  • A
    agillespieAug 27, 2025
    Why does Symmons Temptrol 261XBODY Control Unit delivery temperature reduce gradually during use?
    • H
      Henry WeeksAug 27, 2025
      If the water temperature from your Symmons Control Unit gradually decreases during use, requiring you to turn the handle to hotter positions to maintain a constant temperature, it's likely due to an overdraw on the hot water supply (i.e., running out of hot water). To fix this, reduce the maximum flow by adjusting the volume control on the valve or showerhead. This will allow for a longer period of use before the hot water supply is depleted.
  • D
    Dennis WardAug 31, 2025
    How to fix Symmons Temptrol 261XBODY that will not pass water?
    • S
      Stacy DavisAug 31, 2025
      If your Symmons Control Unit isn't dispensing any water, it's likely that either the hot or cold water supplies (or both) are not turned on. Ensure that both supplies are fully turned on, as the valve requires pressure from both hot and cold water to operate.

Summary

Important For Installer

Mounting Bracket Installation

Determine Wall Type

Valve Body Installation

Install Piping;Fittings

Install valve and connect hot/cold water supply and tub spout pipe.

Set Temperature Limit Stop Screw

Limit stop screw limits handle to prevent scalding; adjust for desired temperature.

Valve Body Test Cap

Install Valve Body with Test Cap

Test cap allows system pressurization during installation; do not remove during wall construction.

Service Instructions

Removing Flow Control Spindle

Steps for removing trim handle, escutcheon plate, cap assembly, and flow control spindle.

Hot;Cold Seat Repair

Service requires specific tools and seats; replace both seats and tighten to 15 foot pounds.

Checking Water Pressure Balancing Piston

Piston should slide freely; tap or soak to free if restricted. Replace spindle if unable to free.

Troubleshooting Chart

Temperature Control Handle Issues

Cause: Restricted piston, overdraw on hot water. Solution: Free piston, replace spindle, or reduce flow.

Incorrect Water Delivery Temperature

Cause: Piped incorrectly or overdraw. Solution: Correct piping or adjust flow.

Symmons Temptrol 261XBODY Specifications

General IconGeneral
BrandSymmons
ModelTemptrol 261XBODY
CategoryControl Unit
LanguageEnglish

Related product manuals