Synco P1T User Manual

Thank you for choosing SYNCO product.
Please read this manual carefully before use and follow all instructions
mentioned herein.
Microphone P1T/P1L
User Manual
Caring For Your SYNCO Product
Package List
Product Instruction
Please keep the product in a dry, clean, dust-free environment.
Keep corrosive chemicals, liquids and heat source away from the product
to prevent mechanics damage.
Use only a soft and dry cloth for cleaning the product.
Malfunction may be caused by dropping, impact of external force.
Do not attempt to disassemble the product. Doing so voids warranty.
Please have the product checked or repaired by authorized technicians if
any malfunctions happened.
Failure to follow all the instructions may result in mechanics damage.
Warranty does not apply to human errors.
TX Transmitter x1 Wireless Charging
Case x1
Charging Cable x1 Type-C to 3.5mm Adapter x1
TX Transmitter
RX Receiver
Wireless Charging Case
① Power
② Working Indicators
③ Built-in Mic
④ Contacts
⑤ Pocket Clip
① Vocal E󽗈ects
② Type-C Port
③ Working Indicators
④ Connector
⑤ Contacts
① Pairing/ Power Prompt
② Type-C Port
③ Working Indicators
④ Contacts
RX Receiver (Type-C or
Lightning Connector) x1
Indicator — Receiver
Indicator — Wireless Charging Case
Indicator — Transmitter (Double press the Power button to turn o󽗈 light
e󽗈ect)
Flash concurrently
Flash concurrently
Illuminate sequentially
Single light keeps on &
Illuminate sequentially
Single light keeps on (In the
case)
Illuminate sequentially (Light
e󽗈ect on)
Single light keeps on (Light
e󽗈ect o󽗈)
Single light 󽗊ashes
Illuminate sequentially
Single light 󽗊ashes twice &
Illuminate sequentially
System unpaired
System unpaired
Pairing
Original sound
Charging, and then turns o󽗈 when fully
charge
System paired, normal working
System paired, normal working
Low battery
System paired
Vocal e󽗈ects on
Working Indicators (White Light)
Working Indicators (White Light)
Working Indicators (White Light)
Working Indicators (Red Light)
Operations
1. Usage
2. Manual Pairing
3. Charging
4. Check the power
5. Use vocal e󽗈ects
① Tap on the right side of charging case to pop
out the drawer
② Take the TX and RX out
③ TX should boot automatically as it leaved the
case, and switch itself o󽗈 automatically when
returning to the case.
① Place the TX and RX in the case with their
contacts are connected with the case’s
② Long press the Pairing button on the case for
3 seconds with the drawer open
③ The indicators on the TX and RX should light
up and illuminate sequentially when pairing is
successful
Note: The transmitter will automatically switch
o󽗈 if it is unpaired or disconnected for 5 minutes.
Charge the TX: Place the TX in the case with
contacts connected with the case’s.
Charge the case: Connect the case with power
supply via the charging cable.
TX: Short press the Power button, the indicators will light up according to
remain power for 5 seconds
Charging Case: Short press the Power Prompt button, the indicators will
light up according to remain power for 5 seconds
Short press the Vocal E󽗈ects button on the receiver to switch sound e󽗈ects:
Original >> Studio FX >> KTV FX >> Voice Ampli󽗉cation >> EDM (Electronic
Dance Music) >> Baby FX >> Male to Female >> Female to Male >> Monster FX.
Default e󽗈ect: Original
Long press for 3 seconds
(Forcible switch: Long press the Power button on TX for 3 seconds)
④ RX should boot automatically as it is plugged into smartphone

Synco P1T Specifications

General

Type	Lavalier Microphone
Transducer	Electret Condenser
Polar Pattern	Omnidirectional
Frequency Response	50Hz-20kHz
Connector	3.5mm TRS
Max SPL	130dB SPL