TC-Helicon VoiceLive User Manual

11
QUICKSTART
• Press the USER Button. You will now hear
the “Telephone Voice” effect. This preset
has the USER button setup to do this
function. (make sure you try singing into the
mic to hear what’s going on)
• Press the HARMONY MUTE button (8) to
turn off the harmonies.
• Press the USER button and then the
HARMONY MUTE button to enable the
harmonies and disable the Telephone Voice
effect.
• Hold the HOLD FOR BYPASS BUTTON (8)
to bypass all effects on VoiceLive.
• Hold the HOLD FOR BYPASS BUTTON (8)
again to enable effects in VoiceLive.
• Press the KEY button (2) followed by the
PREVIOUS/NEXT buttons to change the
key of the harmony scale.
• Press the SCALE button (3) followed by the
PREVIOUS/NEXT buttons to change the
scale type.
• Press the PRESET SELECT (1) button
followed by the PREVIOUS/NEXT buttons to
change the preset number.
Preset Direct Mode
Preset Direct Mode makes the top buttons on
VoiceLive respond like radio station buttons on
a car radio for preset access.
• Hold the DIRECT button (3) when in preset
mode until the LED Text Display flashes
DRCT, putting VoiceLive into Preset Direct
Mode.
• Press any of the top 4 buttons to access the
programmed direct presets.
• Press the PREVIOUS/NEXT buttons to find
a different preset that you like, making sure
that the second character on the LED text
display is a “*”.
• Press and hold one of the top 4 buttons,
until the second character on the LED text
display changes to A, B, C or D. You have
now programmed that button to recall the
desired preset.
Note: Holding a direct button when a preset
has not been changed ("*" is not displayed) will
cause VoiceLive to leave direct mode.
Here's how the LED text Display works in
Preset Direct Mode:
For example: PA23
P: This character indicates that the unit is in
Preset Mode.
A: A,B,C,D means that a Direct preset is
recalled. Holding one of the top 4 buttons
when this is displayed will put VoiceLive
into a new mode. If this character is a “*”
then a Direct preset is not recalled.
Holding one of the 4 top buttons will pro-
gram this button to recall the current pre-
set.
23: This indicates the current preset number.
• Find a preset that you like with lots of
harmony using the PREVIOUS/NEXT
buttons.
• Hold one of the top four buttons to program
a DIRECT button to this preset.
Preset Voice Mode
• Hold the VOICE button (4) until the LED text
display flashes VOIC to put VoiceLive into
Preset Voice Mode.
• Press any of the top four buttons to
enable/disable a harmony voice. Notice that
the Vocal 1 - 4 LEDs to the right of the LCD
display indicate which Voices are enabled.
• Press the PREVIOUS/NEXT buttons to
change presets. Notice that the
enabled/disabled combination of voices do
not change as you change presets.
Here's how the LED text Display works in
Preset Voice Mode:
For example:
PV23
P: This character indicates that the unit is in
Preset Mode.
V: This indicates that VoiceLive is in Voice
Mode.
23: This indicates the current preset number.
Note: Key and Scale may only be changed
with scale type presets. Pressing the KEY (2)
and SCALE buttons when on anything other
than a Scale preset will have no effect.

TC-Helicon VoiceLive Specifications

Analog Inputs

mic impedance	3.6/1.8 kOhm
line impedance	21/13 kOhm
line input level at 0 dBFS	24 dBu to 0 dBu

Analog Outputs

output impedance	40 Ohm
max output level balanced	20 dBu
max output level unbalanced	14 dBu

Operating Environment

operating temperature	32° F to 122° F (0° C to 50° C)
storage temperature	-22° F to 167° F (-30° C to 70° C)
humidity	Max. 90 % non-condensing

Supplementary

dimensions	11.1" x 10.25" x 3.5" (282 x 260 x 89 mm)
weight	5.9 lb. (2.7 kg)
mains voltage	100 to 240 VAC, 50 to 60 Hz (auto-select)