Technics SU-V75 - Page 7

lj LOCATION OF CONTROLS
Peak-power meters (power level meter)
These
meters
indicate
the
peak-power
value
of
the
output
level
to
the
speaker
systems.
Note:
If
speaker
systems
with
an
impedance
of
8
ohms
are
connected,
the
actual
value
can
be
read
directly.
If,
however,
the
impedance
is
16
ohms,
the
actual
output
value
is
1
of
the
indicated
value.
Power switch/indicator
indicated valuex8Q
speaker impedance (Q)
eLoudness switch
Set
to
the
‘‘on”
position
when
listening
to
music
at
low
volume.
Auditory
perception
of
sound
in
the
low
frequency
range
falls
off
at
low
volume,
but
when
the
switch
is
in
this
position,
this
deficiency
is
compensated
for,
so
that
the
full
impact
of
the
musical performance can be enjoyed.
Actual output=
Volume control
This control is
used to raise or lower
the volume (sound)
level.
DAS ame tore ae (TONNE
=
Speakers. 3 7 Seayoit artnet
NG ene
: CD) : : GD : ; « ) :
oa) OIE AE ANI
4 it mun S) ‘Shimane 5) Soman wt 5) ‘Si fgnt
e@Headphones Balance control Input selectors/indicators
iack This control is used to These selectors are used to select the sound
as adjust left/right volume source to be heard, such as a disc, radio
broadcast, etc. (the corresponding indicator
will illuminate.)
Tape
monitor
selectors/indicators
(tape
1/tape
2)
balance.
Speaker selectors
main (M1. _. =): Tone (The indicator will illuminate)
Sound
can
be
heard
from
the
speaker
CONtrols
source
(mH):
systems
connected
to
the
“MAIN”
(bass/treble)
Set
to
this
position
when
one
of
the
input
selectors
is
pressed.
terminals.
The
bass
control
tape
I/tape
1>2
(B=):
remote
(M_.
=):
is
used
to
adjust
Set
to
this
position
to
playback
or
monitor
the
sound
from
tape
deck
of
Sound
can
be
heard
from
the
speaker
_
the
low
range
this
system
or
to
record
from
tape
deck
of
this
system
to
a
second
systems
connected
to
the
“REMOTE”
sound.
The
treble
tape
deck
connected
to
the
‘‘TAPE
2/EXT”
terminals.
terminals.
control
is
used
to
tape/ext
(H__
=):
Note:
adjust
the
high
Set
to
this
position
to
playback
or
monitor
the
sound
from
a
When
only
one
system
of
speakers
is
range
sound.
second
tape
deck
connected
to
the
TAPE
2/EXT
terminals.
connected,
no
sound
will
be
heard
if
Note:
both
selectors
are
pressed.
If
both
tape-monitor
selectors
are
pressed
at
the
same
time,
only
the
sound from second tape deck will be heard.
Main speaker terminal
(Playback)
|
|
(Unswitched)
Tape
2lext—[
(R
ch)
L ch) AC outlets
(Rec
out)
(Switched
}
(>)
FROM
FROM
@
©
FROM
®
TAPE
TUNER
TAPE
2
-
a
geen
pee
Ground
Shon
AC
inlet
CD/aux
(R ch) (L ch)
Tape
deck
(RS-362)
connector
Tape
deck
(RS-362)
Connector
(Power supply)
Tuner (ST-362) connector
Remote speaker terminal