EasyManuals Logo

Teka HLB 8510 P User Manual

Teka HLB 8510 P
Go to English
110 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #44 background imageLoading...
Page #44 background image
44
User Guide
Pyrolysis self-cleaning function
WARNING
Before running the pyrolysis cleaning cycle,
please read the safety instructions given at
the start of the Installation and Maintenance
manual closely.
This function allows you to run a pyrolysis clean-
ing cycle during which, due to the high tempera-
tures reached inside the oven, the accumulated
grease is carbonized.
As a general rule, a pyrolysis cycle should be run
every 4-5 cooking cycles, using the most suita-
ble program for the amount of dirt in the oven.
The more dirt, the longer the program.
During the pyrolysis cycle, the light inside the
oven remains off.
PROGRAM THE PYROLYSIS FUNCTION
IMPORTANT
Before starting the pyrolysis function, you
must remove all the accessories and dishes
from the oven, including the supports of the
tray and/or telescopic guides. Follow the in-
structions given in the Installation and Main-
tenance Manual provided with your oven.
WARNING
Remove any spills or excess dirt from the in-
side of the oven, as these could catch fire
during the pyrolysis function with the conse-
quent risks.
WARNING
Before starting the pyrolysis check that the
oven door is correctly closed.
1. Turn the cooking control dial to Pyrolysis:
.
2. After a few seconds, symbol
lights up
on the clock display and indication P2 is
read (pyrolysis program 2).
3. Now you can change the pyrolysis program
to P1, P2, P3 using keys
or :
P1: Mild pyrolysis. One hour.
P2: Normal pyrolysis. One and a half hours.
P3: Intensive pyrolysis. Two hours.
4. After selecting the required program, press
. Immediately afterwards, the automatic
door lock is activated.
WARNING
If the door is not correctly closed, it will not
lock, an alarm is heard and the pyrolysis will
not start.
If this happens, switch off the alarm by
pressing any key on the clock, close the
door correctly, turn the control dial to
and
select the pyrolysis program again, following
the instructions above.
5. When the door is locked, symbol
lights
up on the clock display and the time re-
maining until the end of the pyrolysis func-
tion is displayed.
IMPORTANT
At this point, the oven is programmed and
runs the pyrolysis cleaning cycle. While this
cycle is running, it is not possible to select
any of the oven clock functions, except the
child safety function.
Do not try to open the oven door as this may
interrupt the cleaning process.
6. When the pyrolysis cleaning ends, a beep is
heard, symbol
flashes and 0:00 is dis-
played on the clock.
7. Press any key on the clock to stop the
beeping.
8. Turn the control dial to position
.
9. The oven heating process has ended.
However, the oven is too hot and cannot
be used.
The cooling function will continue and the

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Teka HLB 8510 P and is the answer not in the manual?

Teka HLB 8510 P Specifications

General IconGeneral
Oven sizeMedium
Oven typeElectric
Cleaning typePyrolytic
Bottom heatingYes
Number of ovens1
Total oven power- W
Full surface grill-
Bottom heating power1050 W
Total oven(s) interior capacity70 L
Door hingedown
Cord length1.9 m
Control typeButtons, Touch
Display typeLED
Door materialGlass
Product colorBlack
Control positionFront
Oven door openingDrop down opening
Appliance placementBuilt-in
AC input voltage220 - 240 V
Energy consumption (conventional)0.88 kWh
Energy consumption (forced convection)0.68 kWh
Weight and Dimensions IconWeight and Dimensions
Width595 mm
Installation compartment depth490 mm
Installation compartment width568 mm
Installation compartment height590 mm
Interior dimensions (W x D x H)475 x 402 x 364 mm
Installation compartment width (min)560 mm

Related product manuals