Tektronix TDS 684A

To Next Page

To Previous Page

Operating Interface Maps

2–4

TDS 684A, TDS 744A, & TDS 784A User Manual

Front Panel Map — Right Side

Hardcopy, page 3–120

File System, page 3–117

Autoset, page 3–5

Help, page 3–135

Status, page 3–133

Selecting Channels,

page 3–7

Horizontal Controls,

page 3–13

Acquisition Modes, page 3–20

Cursor Measurements, page 3–97

Triggering, page 3–49

Delay Triggering, page 3–80

Edge Triggering, page 3–57

Logic Triggering, page 3–60

Pulse Triggering, page 3–70

Color, page 3–33

Display Settings,

page 3–27

Remote

Communication,

page 3–128

Vertical Controls,

page 3–10

Measurement System, page 3–87

Saving and Recalling

Setups, page 3–111

Saving and Recalling

Waveforms, page 3–114

File System, page 3–117

Waveform Math,

page 3–142

Zoom, page 3–37

Probe Calibration,

page 3–104

Ground

Cursor

Measurements,

page 3–97

InstaVu,

page 3–43

(TDS 700A

models only)

Main Page

Table of Contents10
Table 1-1: Key Features of the TDS Oscilloscopes23
Figure 1-1: Rear Panel Controls Used in Start up26
Figure 1-2: ON/STBY Button27
Table 1-2: Fuse and Fuse Cap Part Numbers27
Figure 2-1: Connecting a Probe for the Examples (P6245 Shown)38
Figure 2-2: SETUP Button Location39
Figure 2-3: the Setup Menu39
Figure 2-4: Trigger Controls40
Figure 2-5: the Display after Factory Initialization41
Figure 2-6: the VERTICAL and HORIZONTAL Controls42
Figure 2-7: TRIGGER Controls43
Figure 2-8: AUTOSET Button Location43
Figure 2-9: the Display after Pressing Autoset44
Figure 2-10: Display Signals Requiring Probe Compensation44
Figure 2-11: the Channel Buttons and Lights45
Figure 2-12: the Vertical Main Menu and Coupling Side Menu46
Figure 2-13: the Menus after Changing Channels47
Figure 2-14: Measure Main Menu and Select Measurement Side Menu49
Figure 2-15: Four Simultaneous Measurement Readouts50
Figure 2-16: General Purpose Knob Indicators51
Figure 2-17: Snapshot of Channel 152
Figure 2-18: Save/Recall Setup Menu54
Figure 3-1: How Probe Compensation Affects Signals60
Figure 3-2: P6139A Probe Adjustment60
Table 3-1: Autoset Defaults62
Figure 3-3: the Channel Readout64
Figure 3-4: Waveform Selection Priority65
Figure 3-5: Scaling and Positioning66
Figure 3-6: Vertical Readouts and Channel Menu67
Figure 3-7: Record View and Time Base Readouts69
Figure 3-8: Horizontal Controls70
Figure 3-9: Acquisition: Input Analog Signal, Sample, and Digitize73
Figure 3-10: Several Points May be Acquired for each Point Used73
Table 3-2: How Interleaving Affects Sample Rate75
Table 3-3: Additional Resolution Bits78
Table 3-4: TDS 744A Sampling Mode Selection80
Table 3-5: TDS 784A Sampling Mode Selection81
Table 3-6: XY Format Pairs88
Table 3-7: Pattern and State Logic118
Table 3-8: Pulse Trigger Definitions127
Table 3-9: Measurement Definitions144
Table 3-10: Probe Cal Status165
Table A-2: Standard Accessories230
Table A-1: Options231
Table A-3: Optional Accessories231
Table A-4: Accessory Software232
Table D-1: Factory Initialization Defaults250

Tektronix TDS 684A - Page 33

Table of Contents

Other manuals for Tektronix TDS 684A

Related product manuals