Textron Bob-Cat - Height of Cut Settings - Side Discharge

23
HYDRO
MIDSIZE
Use only these setting combinations. If any other combinations are used, quality of cut may suffer because the
blade angle is wrong. Heights of cut shown were measured in a controlled workshop environment. Slight
variations can occur in the field, depending on tire pressures, etc. For side discharge decks, make sure the
front of the blade is lower than the back of the blade (as shown below) to prevent double cutting.
Ç
È
1/2" MAX
Î
FRONT














































































































































































































































SIDE DISCHARGE
WHEEL MOTOR
LOW CUTTING POSITION
WHEEL MOTOR
HIGH CUTTING POSITION
CUTTER
DECK
POSITION
NUMBER
OF BLADE
SPACERS
NUMBER OF
CASTER
SPACERS
HEIGHT
OF CUT
NUMBER OF
CASTER
SPACERS
HEIGHT
OF CUT
1/4"
SIZE
1/2"
SIZE
8"
CASTER
9"
CASTER
1/4"
SIZE
1/2"
SIZE
8"
CASTER
9"
CASTER
1
2
0 0 1-1/8" 1-1/4" 0 2 2-15/16" 3-1/8"
1 0 1-5/16" 1-3/8" 1 2 3-1/8" 3-5/16"
0 1 1-1/2" 1-5/8" 0 3 3-1/4" 3-1/2"
1
0 0 1-3/8" 1-1/2" 0 2 3-3/16" 3-3/8"
1 0 1-9/16" 1-5/8" 1 2 3-3/8" 3-9/16"
0 1 1-3/4" 1-7/8" 0 3 3-1/2" 3-3/4"
0
0 0 1-5/8" 1-3/4" 0 2 3-7/16" 3-5/8"
1 0 1-13/16" 1-7/8" 1 2 3-5/8" 3-13/16"
0 1 2" 2-1/8" 0 3 3-3/4" 4"
2
2
1 0 1-1/2" 1-5/8" 1 3 2-7/8" 3-1/16"
0 1 1-3/4" 1-13/16" 0 4 3-1/16" 3-1/4"
1 1 1-15/16" 2" 1 1 3-1/4" 3-7/16"
1
1 0 1-3/4" 1-7/8" 1 3 3-1/8" 3-5/16"
0 1 2" 2-1/16" 0 4 3-5/16" 3-1/2"
1 1 2-3/16" 2-1/4" 1 1 3-1/2" 3-11/16"
0
1 0 2" 2-1/8" 1 3 3-3/8" 3-9/16"
0 1 2-1/4" 2-5/16" 0 4 3-9/16" 3-3/4"
1 1 2-7/16" 2-1/2" 1 1 3-3/4" 3-15/16"
3
2
1 2 2-1/2" 2-5/8" 1 4 3-5/8" 3-11/16"
0 3 2-11/16" 2-3/4" 0 5 3-3/4" 3-7/8"
1 3 2-7/8" 2-15/16" 1 5 3-15/16" 4-1/16"
1
1 2 2-3/4" 2-7/8" 1 4 3-7/8" 3-15/16"
0 3 2-15/16" 3" 0 5 4" 4-1/8"
1 3 3-1/8" 3-3/16" 1 5 4-3/16" 4-5/16"
0
1 2 3" 3-1/8" 1 4 4-1/8" 4-3/16"
0 3 3-3/16" 3-1/4" 0 5 4-1/4" 4-3/8"
1 3 3-3/8" 3-7/16" 1 5 4-7/16" 4-9/16"
HEIGHT OF CUT - SIDE DISCHARGE