Thermo Pride OME-72D36 User Manual

THERMO PRODUCTS, LLC.
POST OFFICE BOX 237
DENTON, NC 27239
PHONE: 800-476-4328
MO-487
ECN 5577-MA 190924
MADE IN USA
OIL-FIRED FURNACE
DOWN FLOW & DIRECT VENT (SEALED COMBUSTION)
MODEL: OME-72D36 / OME-72T36
INSTALLATION AND SERVICE MANUAL
For installation in:
1. Manufactured Homes
2. Modular Homes/Buildings
3. Site Construction—Residential
:
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
: If the information in these instructions is not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
: Improper installation, adjustment, alteration, service, or maintenance can cause injury or
property damage. Refer to this manual. For assistance or additional information consult a qualified installer,
service agency, or fuel supplier.
: Do not use this appliance if any part has been underwater. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the electrical or control system that has been
underwater.
PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION, INITIAL FIRING, AND BEFORE
PERFORMING ANY SERVICE OR MAINTENANCE. THESE INSTRUCTIONS MUST BE LEFT WITH THE USER
AND SHOULD BE RETAINED FOR FUTURE REFERENCE BY QUALIFIED SERVICE PERSONNEL.

Thermo Pride OME-72D36 Specifications

General

Brand	Thermo Pride
Model	OME-72D36
Category	Furnace
Language	English

Summary

General Safety Warnings

Furnace Safety Precautions

General safety warnings regarding flammable liquids, proper operation, and potential hazards.

Gas Leak Emergency Response

Step-by-step instructions for responding to a gas leak to ensure safety.

I. SAFETY SECTION

Operational Safety Warnings

Critical warnings on fuel usage, maintenance, and environmental safety around the furnace.

IV. INSTALLATION

Roof Jack and Chimney Installation

Procedures for installing roof jacks and standard chimneys for proper venting.

Furnace Location and Base Installation

Guidelines for furnace placement and installation on various bases.

Alcove, Closet, and Combustion Air

Installation requirements for alcove/closet placement and combustion air supply.

G. Combustion Air Requirements

Ensuring adequate combustion air supply for efficient and safe furnace operation.

III. FURNACE SPECIFICATIONS

Burner and Blower Data

Details on burner type, nozzle, oil pump, and blower performance characteristics.

H. FUEL PIPING

Oil Tank and Piping Installation

Guidelines for oil supply lines, tank placement, and safety regulations.

J. ELECTRICAL WIRING

Electrical Supply and Thermostat Wiring

Connecting power supply, thermostat, and controlling circuits for furnace operation.

Blower Controller and Wiring

Blower Controller Terminal Definitions

Explanation of terminal functions for the blower controller and harness.

Blower Operating Modes

Details on standby, fan, cooling, and dehumidification modes of operation.

Heat Mode and Blower Delay Settings

Operation during heat mode and selection of blower on/off delay times.

K. BURNER INSTALLATION

Oil Burner Installation Procedure

Detailed process for installing the burner, including electrical and fuel connections.

L. BURNER OPERATION AND ADJUSTMENT

Burner Lighting and Setup Instruments

Required instruments and steps for the first lighting and setup of the burner.

Combustion Analysis and Parameters

Methods for analyzing combustion and achieving optimal efficiency with CO2, O2, CO, and smoke.

V. DEALER MAINTENANCE

Troubleshooting Furnace Issues

Systematic troubleshooting steps and flowcharts for diagnosing furnace problems.

Cad Cell and Heat Exchanger Maintenance

Procedures for checking the cad cell and cleaning the heat exchanger.

Flue Pipe and Extended Shutdown

Guidelines for inspecting flue pipes and preparing the furnace for extended shutdown.

VI. USER INFORMATION SECTION

User Warnings and Cautions

Important warnings and cautions for furnace users regarding operation and safety.

Component Locations and Inspections

Diagrams showing component locations and areas requiring regular inspection.

Filter Maintenance and Contact Info

Instructions for filter cleaning and contact details for service and installation.

Appendix A. Replacement Parts List

Parts Identification and Numbers

Detailed breakdown of furnace components with corresponding part numbers and quantities.