ETC009 - ETC010
First issue 01 / 06
OP05
U0C300C 1 . 8 2005. 07 . 20-01
VAI Amplitude 12%
VA0/VA1 Amplitude +5%
FC0 OFF
VG2 MODE LIGHT LINE
DSS Normal operation
DSG 0dB
OP05 : default value : 00100111
Bit 0 : VAI (gain correction; 0: no correction 1: +12% PAL I).
Bit 1-Bit 2 : VA0/VA1
(IF CVBS output amplitude correction; 10: +5%
).
Bit 3 : OFB (Offset control on Red and Blue channel).
Bit 4 : FCO (force color on when bad signal, color killer not active).
Bit 5 :
VG2 MODE
(0:OSD indication 1:Line).
Bit 6 : DSS (0: normal operation 1: LCD / Pscan
Bit 7 : DSG (audio output selection amplitude; 0: 0dB)
OP06
U0C300C 1 . 8 2005. 07 . 20-01
DCXOMUX Nicam
QSS QSS Amp active
FMI Output conn to QSS0
NICAM ON
RPA0/1 1:1
RP00/1 1:1
OP06 : default value : 00001011
Bit 0 : DCXOMUX (0:P3DCX0 TDA12070/12072/without NICAM
1: NICAM).
Bit 1 : QSS
(validation QSS amplifier; 1: active
).
Bit 2 : FMI (connexion QSS AMP output to SSD module or sound
PLL demodulator; 0: Output conn to QSS0).
Bit 3 : NICAM (NICAM selection; 1: ON)
Bit 4-Bit 5 :
RPA0 /1 (00)
Bit 6-Bit 7 : RPO0/1
(00)
OP07
U0C300C 1 . 8 2005. 07 . 20-01
PWL 3
SOC0/1 0% above PWL
PWL ON PWL circuit active
GD BG DK Group delay correction
OP07 : default value : 11000011
Bit 0-1-2-3 : PWL (peak white limit; default : 3)
Bit 4-Bit 5 : SOC0/1
(% above PW level; 00: 0% above PWL
).
Bit 6 : PWL ON (activation of the peak white limiting circuit; 1: active)
Bit 7 : GD BG DK (activation of the Group delay correction;
0: group correction)
OP08
U0C300C 1 . 8 2005. 07 . 20-01
No use OFF
OP08 : default value : 00000000
Bit : OFF (No use)
OP09
U0C300C 1 . 8 2005. 07 . 20-01
AFG False
TYUV1 False
BPBS True
CLF True
BWYC False
CBPS False
SLD False
OSB False
OP09 : default value : 00001100
Bit 0 : AFG (AFC measurement; 0: AFC False)
Bit 1 : TYUV1(Analog output selection for text; valid if TYUV0=1)
Bit 2 : BPBS (Enable bypass of sound filter at stereo mode)
Bit 3 : CLF (Comb filter diode clamp; set to1)
Bit 4 : BWYC (Bandwidth of anti aliasing filter at YC mode of
3.58MHz systems; 0: False)
Bit 5 : CBPS (Internal chroma bandpass filter mode; 0: False)
Bit 6 : SLD (Sleep mode detector status; 0: sleep enabled, False)
Bit 7 : OSB (width of Burstkey; 0: False burstkey=3.52us)
OP10
U0C300C 1 . 8 2005. 07 . 20-01
BKC False
TYUV0 False
QDT False
TCCON True
TCI2X True
TXTS False
Blue SCN False
OP10 : default value : 00110000
Bit 0 : BKC (Internal burst key position; 0: False normal position)
Bit 1 : TYUV0 (TXT/CC output selection; 0: False, RGB format)
Bit 2 : QDT (Q values of Second chroma trap; 0: False)
Bit 3 : FBC1 (Fixed beam current during switch off; 0: False, 1mA)
Bit 4 : TCCON (Top sync. clamp control; 1: True , active)
Bit 5 : TCI2X (Top sync. clamp time constant; 1: True)
Bit 6 : TXTS (TXTS Mode : TEXT source; 0: False TXT from CVBS)
Bit 7 : Blue SCN (Blue screen with no signal; 0: False)
To Next Page
Loading...
