EasyManuals Logo

TIC GS5 User Manual

TIC GS5
10 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
Before you begin the installation of your new TIC outdoor product, please
carefully select the locations of your new TIC products.
In general;
1. Select a reasonably level surface for the installation of your new TIC
outdoor speakers. For surface speakers this will prevent movement or
excessive vibration during use. This will also ensure more uniform
sound dispersion.
2. Ensure your new TIC outdoor speaker cables or power source if
required, can easily reach your new speakers. Some people even pre-
lay string as a guide ensuring that there are no obstructions or
difficulties such as concrete paths or architectural feature impediments.
While most if not all TIC outdoor speakers use and recommend burying
the cable lightly 4-6 inches, if the cable is surface mounted you must
make sure the cable is placed where it cannot be tripped over, pulled,
abraded or crushed.
3. Do not place your TIC outdoor speakers in a depression or area where
water pools or in the direct path of sprinklers.
4. Wherever possible avoid long term exposure of your new TIC outdoor
speakers to chlorinated solvents, acids such as those often contained
in fertilizers and other solvents which have the potential to eventually
wear the components prematurely.
5. When installing either burial cable or TIC’s in-ground outdoor speakers
please be very aware of any submerged plumbing, piping such as
sprinklers or irrigation and wiring already in existence.
A note on Speaker Cable;
TIC recommends the use of our SPC30, 50 or 100’ double insulated high
quality speaker cable, however just about any reasonable speaker cable may
be used including existing runs that may be in place. For standard 8Ω
installations of 10 25ft., just about any 16/18 gauge 2 core cables can usually
be used although we would prefer a double insulated or burial spec cable be
used. For longer runs of 25 100ft. 10/14 gauge cable can be used however
resistance down the line will become a contributing factor.
Please visit TIC Corporations website at www.ticcorp.com and review the
Audio Installation Basics articles under Technical Resources for more in depth
exterior audio and cable guidelines.

Other manuals for TIC GS5

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TIC GS5 and is the answer not in the manual?

TIC GS5 Specifications

GS3

Speaker Specifications IconSpeaker Specifications
speaker_driver5.25” full range Co-Axial Driver
wooferInjection molded PP cone with Butyl rubber surround
tweeter1" aluminum
Acoustic Performance IconAcoustic Performance
frequency_response67Hz – 19kHz
sensitivity86db ± 3db
power_handling50 / 100W
Dimensions and Weight IconDimensions and Weight
unit_size12.5x12.5x12.5 inches
unit_weight10 Lbs
pack_size13x13x13 inches

GS5

Speaker Specifications IconSpeaker Specifications
speaker_driver5.25” full range Co-Axial Driver
wooferInjection molded PP cone with Butyl rubber surround
tweeter1" aluminum
Acoustic Performance IconAcoustic Performance
frequency_response67Hz – 19kHz
sensitivity86db ± 3db
power_handling50 / 100W
Dimensions and Weight IconDimensions and Weight
unit_size8.8x8x8 inches
unit_weight5.2 Lbs
pack_size10x17x9 inches

GS10

Speaker Specifications IconSpeaker Specifications
speaker_driver8” full range Co-Axial Driver
wooferInjection molded PP cone with Butyl rubber surround
tweeter1" aluminum
Acoustic Performance IconAcoustic Performance
frequency_response36Hz – 19kHz
sensitivity89db
power_handling100 / 200W
Dimensions and Weight IconDimensions and Weight
unit_size13.7x6.5x6.5 inches
unit_weight3 Lbs
pack_size12x14.5x7.5 inches

Related product manuals