What does it mean if the warning buzzer is “ON” on my TOHATSU MFS 30C?
If the warning buzzer is ON on your TOHATSU Outboard Motor, it could indicate a defective power tilt switch or solenoid. Inspect and replace the power tilt switch or solenoid.
How to troubleshoot a TOHATSU MFS 30C Outboard Motor that is difficult to start?
If your TOHATSU Outboard Motor engine is difficult to start, several factors could be at play. Start by refilling the fuel tank if it's empty. Ensure the fuel system is correctly connected and inspect the fuel line for any air leaks, sealing them as necessary. Replace any deformed or damaged fuel hose. Also, make sure the air vent on the fuel tank is open. Clean or replace any clogged fuel filter, vapor separator, or fuel pump. If the fuel pump is malfunctioning, it should be repaired or replaced. Verify that you are using the recommended engine oil and the correct type of gasoline. Lastly, inspect and clean the high pressure fuel pump if it shows low performance or clogging.
What to do if my TOHATSU MFS 30C has low engine speed or poor boat speed?
If your TOHATSU Outboard Motor exhibits low engine speed or poor boat speed, several issues could be responsible. Start by checking and correcting the compression. Clean the combustion chamber to remove carbon deposits. Adjust the valve clearance if it's incorrect. Check the oil pressure and address the cause if it's low, also check for oil pump failure or a clogged oil filter. Inspect and repair the cooling system if there is insufficient cooling water flow or a defective pump. Adjust the valve timing if it's incorrect due to timing belt elongation or incorrect installation. Replace faulty valve seals. Inspect and replace worn components if there is excessive wear of the piston, piston ring, or cylinder. Ensure the spark plug is properly tightened.
General| Brand | TOHATSU |
|---|---|
| Model | MFS 30C |
| Category | Outboard Motor |
| Language | English |
Welcome message and introduction to the outboard motor.
Importance of warranty card registration for ownership.
Confirmation of dealer inspection before delivery.
Space to record the serial number for future reference.
Explains the meaning of safety alert symbols used in the manual.
Operator's duty for safety, knowledge, and following regulations.
Explanation of the stop switch lanyard's role in safety.
Mandate for operators and passengers to wear PFDs.
Emphasizes using authorized shops and genuine parts.
Highlights hazards like carbon monoxide and gasoline flammability.
Compares key features across different models (F25C, F30C).
Explains the meaning of characters in the model name.
Detailed technical specifications for MF and E models.
Detailed technical specifications for ET models.
Labeled diagram of parts for the MF model.
Labeled diagram of parts for the E model.
Labeled diagram of parts for the ET model.
Labeled diagram for remote control and fuel tank components.
Visual guide to the location of various warning labels on the motor.
Covers manual reference, hot surfaces, starting, and warning lamps.
Warnings related to stop switch and lanyard usage.
Precautions regarding gasoline flammability and handling.
Instructions for laying down the outboard motor.
Warnings about gasoline storage and tank cap usage.
Warnings related to fuel tank, primer bulb, and connectors.
Specific instructions for using the fuel tank cap.
Reminder to consult the owner's manual.
Location and explanation of the ECI label.
Safe methods for hanging and mounting the motor.
Guidance on the correct placement on the boat's transom.
Proper alignment of the anti-ventilation plate to the hull.
Steps for securing the outboard motor using bolts.
Mounting steps for the PT type using bolts.
Warnings and steps for connecting the battery.
Installing the Tohatsu Onboard Communication System.
Safe handling of gasoline, including types and alcohol content.
Steps and precautions for safely filling the fuel tank.
Instructions on how to correctly fill the engine oil.
Specific oil types, viscosity, and required volume.
Steps for breaking in new engine components.
How warning buzzers and lamps alert the operator.
Identifies where warning buzzers and lamps are situated.
Table detailing warning signals and corresponding issues.
Specific actions to take for identified faults.
Importance and procedure for checking engine oil.
Steps for priming the fuel system.
General procedures and safety for starting the motor.
Step-by-step guide for tiller handle models.
Starting process for electric start models.
Starting process for multi-function tiller models.
Starting process for side mount remote control models.
Setting the control lever to neutral.
Verifying the warning lamp operates correctly.
How to start the engine using the emergency rope.
Importance and duration for engine warm-up.
Idling speed specifications and remarks.
How to use the free throttle lever.
Adjusting engine speed for trolling.
Procedures for shifting and accelerating safely.
Shifting and acceleration for tiller handle models.
Shifting and acceleration for side mount RC models.
Safe procedures for shutting down the engine.
Stopping procedure for side mount RC models.
How to stop the engine quickly in an emergency.
How to steer the outboard motor using tiller or remote.
Information on the spare emergency stop switch.
Importance and methods for adjusting trim angle.
Steps for adjusting trim on manual tilt models.
Steps for adjusting trim on power tilt models.
Procedures for tilting the motor.
Steps for tilting up and down with manual tilt.
Steps for tilting up and down with power tilt.
Using the manual valve for tilting.
Precautions and procedures for operating in shallow water.
Setting for shallow water running with manual tilt.
Setting for shallow water running with power tilt.
Steps to detach the motor from the boat.
Safety guidelines for transporting the motor.
Important considerations when trailering with the motor attached.
Securing the motor for trailer transport with tiller handle.
How to adjust the steering friction lever.
How to adjust throttle grip friction.
Adjusting friction on remote control levers.
Adjusting throttle friction on side mount controls.
How to adjust the trim tab for steering correction.
Importance of daily and periodic maintenance.
Essential checks before and after operating the motor.
Procedures for checking and adding engine oil.
How to clean and flush the motor.
Connecting a hose for flushing the motor.
Procedure for flushing using a test tank.
Steps for safely replacing a blown fuse.
Regular maintenance intervals and tasks.
Step-by-step guide for changing engine oil.
How to replace the engine oil filter.
Procedures for cleaning fuel filters and tank.
Cleaning/replacing the fuel filter in the tank.
Steps for draining and refilling gear oil.
Warnings and safety for propeller replacement.
How to inspect, gap, and replace spark plugs.
How and when to replace the sacrificial anode.
How to check the oil level in the power tilt unit.
Locations where waterproof grease should be applied.
Steps for preparing the motor for storage.
Specific tasks for the engine during storage.
How to use fuel stabilizer for long-term storage.
Procedure for draining all fuel from the system.
Proper procedures for storing the battery.
Steps before using the motor after off-season.
Emergency steps if the motor is submerged.
Safety measures for cold weather operation.
What to do if the motor hits an object.
Considerations for running multiple engines.
Common fuel system problems and their remedies.
Solutions for compression, oil, and miscellaneous problems.
Inventory of tools and spare parts provided.
Table showing propeller marks and sizes for different boats.
Explains emissions and control mechanisms like ignition timing.
How the fuel injection system manages emissions.
Issues that can impact emission compliance.
Recommends using Tohatsu Genuine parts for emission systems.
Specifications for fuel hoses in US and Canada.
EPA requirements for portable fuel tanks.
Requirements for primer bulb and hose assemblies.
Refers to the maintenance schedule on page 70.
Explanation of the CARB star label system.
Details on the One Star Low Emission label.
Details on the Two Star Very Low Emission label.
Details on the Four Star Super Ultra Low Emission label.
To Next Page
