Top Flite Elder 40 User Manual

WARRANTY.....Top Flite Models guarantees this kit to be free of defects in both material and workmanship at the date of purchase. This warranty does
not cover any component parts damaged by use or modification. In no case shall Top Flite‘s liability exceed the original cost of the purchased kit. Further, Top Flite reserves
the right to change or modify this warranty without notice. In that Top Flite has no control over the final assembly or material used for final assembly, no liability shall be assumed
nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product the user accepts all
resulting liability. If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to immediately return this kit in new
and unused condition to the place of purchase.
Top Flite Models 3002 N. Apollo Dr., Suite 1, Champaign, IL 61822 Technical Assistance Call (217)398-8970 productsupport@top-flite.com
READ THROUGH THIS INSTRUCTION BOOK FIRST. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.
USA
MADE IN
ELD4P03 for TOPA0215 V1.1Entire Contents © Hobbico, Inc 2012
Wingspan: 65 in [1650mm]
Wing Area: 778 sq in [50.2 dm²]
Weight: 5.5 – 7.0 lbs [2500 - 3182g]
Wing Loading: 16 – 21 oz/sq ft
[50–64 g/dm²]
Length: 49.5 in [1257mm]
™

Top Flite Elder 40 Specifications

General

Brand	Top Flite
Model	Elder 40
Category	Toy
Language	English

Summary

WARRANTY

INTRODUCTION

SAFETY PRECAUTIONS

Critical Safety and Assembly Guidelines

Comprehensive safety rules covering assembly, operation, and pilot experience.

ADDITIONAL ITEMS REQUIRED

Hardware and Accessories

Lists required hardware and accessories with order numbers for the model.

Adhesives and Building Supplies

Lists essential adhesives and building supplies recommended for construction.

Optional Supplies and Tools

Lists optional tools that can assist in building the model.

IMPORTANT BUILDING NOTES

Key Construction Tips and Considerations

Essential advice on test fitting, glue selection, epoxy usage, and part handling.

GET READY TO BUILD

Initial Preparation Steps

Steps for unrolling plans, unpacking parts, and organizing components.

DIE-CUT PATTERNS

BUILD THE TAIL SURFACES

Build the Stab

Instructions for constructing the horizontal stabilizer of the model.

Build the Elevator

Instructions for constructing the elevator component of the model.

BUILD THE FIN AND RUDDER

BUILD THE WING

Frame the Wing

Steps to construct the basic frame of the airplane wing.

Install the Wing Joiners

Instructions for joining the two wing panels together using joiners.

Join the Wings

Detailed instructions for joining the two wing panels together.

Build the Aileron

Steps to construct the aileron control surface for the wing.

Finish the Wing

Final steps to complete the wing assembly before further construction.

BUILD THE FUSELAGE

Frame the Fuselage

Instructions for building the primary structure of the model's fuselage.

Mount the Wing to the Fuselage

Steps to attach the completed wing assembly to the fuselage structure.

Finish the Fuselage

Final steps to complete the fuselage structure.

Assemble and Install the Landing Gear

Tail Skid Construction and Installation

Tail Wheel Wire Installation

FINAL CONSTRUCTION

Mount the Engine

Instructions for mounting the engine to the firewall.

Install the Radio

Steps for installing the radio system components into the model.

FINISHING

Fuelproofing

Process of protecting the model from fuel and exhaust residue.

Prepare the Model for Covering

Steps to prepare the model's surfaces for covering material.

Cover your Model with MonoKote

Guidance and tips for applying MonoKote covering material.

Installing the Stab and Fin

Join the Control Surfaces

Install the Elevator, Rudder Pushrods and Control Horns

Install the Aileron Pushrods and Control Horns

Scale Details

Optional cosmetic details to enhance the model's appearance.

Kingposts and Flying Wires

Instructions for installing kingposts and simulating flying wires.

Machine Gun

Cockpit and Pilot

Final Hookups and Checks

CONTROL THROWS

GET YOUR MODEL READY TO FLY

Balance your Model

Crucial steps for achieving the correct center of gravity (CG) for stable flight.

PREFLIGHT

Pre-Flight Checks and Procedures

Essential checks before flying, including model identification, battery charging, propeller balancing, and radio checks.

CHECK LIST

Checklist Item 1: Fuelproofing

Protect fuel-exposed areas like firewall and engine compartment from residue.

Checklist Item 2: CG Check

Verify the model's Center of Gravity (CG) against manual specifications.

ENGINE SAFETY PRECAUTIONS

AMA SAFETY CODE (excerpt)

FLYING

Takeoff

Instructions and tips for performing a safe takeoff.

Flight

Characteristics and capabilities of the Elder model during flight.

Landing

Guidance and tips for performing smooth and safe landings.