INTRODUCTORY COMMENT
Thank you for choosing our machine. This
floor-cleaning machine is used for industrial and
commercial cleaning and is able to clean any
type of floor. During its forward movement, the
action of the brush and the detergent solution
removes the dirt, which is picked up by the
suction system, resulting in a dry surface.
The machine must be used only for this purpose.
It gives the best performance when it used
correctly and maintained properly. Therefore,
we ask that you read this instruction booklet
carefully whenever difficulties arise in the
course of the machine’s use. If needed, please
contact our service department for advice and/or
service.
GENERAL RULES
The rules below have to be followed carefully in
order to avoid damage to the machine and
injuries to the operator.
- Read the labels carefully on the machine. Do
not cover them for any reason and replace them
immediately if damaged.
- The machine must be used exclusively by
authorized staff that has been instructed for its
use.
- When using the machine, pay attention to
other people, especially children.
- In case of danger, immediately use the
emergency brake.
- To park the machine, take off the key and put
on the parking brake.
- Do not mix different detergents to avoid
harmful odors.
- Do not place any liquid containers onto the
machine.
- The storage temperature has to be between -
13°F and +131°F.
- The operating temperature should be between
32°F and 104°F.
- The humidity should be between 30 and 95%.
- Do not use the machine in an explosive
atmosphere.
- Do not use the machine as a means of
transportation.
- Do not use acidic solutions, which could
damage the machine and/or injure people.
- Do not use the machine on surfaces covered
with flammable liquids or dust (for example
hydrocarbons, ashes or soot).
- In case of fire, use a powder fire-extinguisher.
Do not use water.
- Watch out for shelves and/or scaffoldings
when operating the machine.
- Use the appropriate speed based on floor
conditions (type of floor, dirtiness, etc.).
- Do not use the machine on areas that have a
higher gradient than the one stated on the
number plate.
- The machine has to carry out simultaneously
the operations of washing and drying. Different
operations must be carried out in restricted areas
prohibited to non-authorized personnel.
- Signal the areas of moist floors with suitable
signs.
- If the machine does not work properly, check
by conducting simple maintenance procedures.
Otherwise, contact an authorized technical
assistant for advice.
- When parts are required, ask for ORIGINAL
spare parts from the distributor or an authorized
dealer.
- Use only ORIGINAL brushes.
- When cleaning and performing maintenance
operations, disconnect the power supply plug
from the machine.
- Do not wash the machine with corrosive
material, direct water jets or high water
pressure.
- Every 200 working hours, have the machine
checked by an authorized service center.
- In order to avoid scales on the solution tank
filter, do not fill the detergent solution hours
before it is used.
- Before using the machine, check that all
panels and coverings are in position as indicated
in this use and maintenance catalog.
- Be sure the recovery tank is empty before
lifting it.
- Restore all electrical connections after any
maintenance operation.
- When your machine has to stop activity,
provide the appropriate waste disposal for its
materials, especially oils, battery and electronic
components. Consider that the machine itself
has been constructed by recyclable materials.
SYMBOLS
Symbol denoting the solution
valve.
Indicates the solution valve lever.
Indicates the signal lamp of the
solenoid valve functioning.
Symbol denoting the brush.
Indicates the switch of the brush
motor.
Symbol denoting the vacuum
motor. Indicates the switch of the
vacuum motor.
Symbol denoting up – down of the
squeegee. Indicates the squeegee
lever.
Symbol denoting the charge level
of the batteries.
Symbol denoting the hour meter.
Indication of the maximum
temperature of the solution
detergent.
It is placed near the charging hole
of the solution tank.
Symbol denoting the brake.
Indicates the signal lamp of the
brake on.
Symbol denoting the brake.
Indicates the lever of the
emergency and parking brake.
Symbol denoting the brush release.
Indicates the push button used to
release automatically the brushes.
Symbol denoting the open book.
Indicates that the operator has to
read the manual before the use of
the machine.
Warning symbol.
Read carefully the sections marked
with this symbol, for the security
of both the operator and the
machine.
To Next Page
Loading...
Need help?
General
