Toro 03678 - Using the Cutting-Unit Kickstand; Applying the CE Decals

To Next Page

To Previous Page

UsingtheCutting-Unit

Kickstand

Partsneededforthisprocedure:

Cutting-unitkickstand

Procedure

Wheneveryoumusttipthecuttingunittoexposethe

bedknife/reel,propuptherearofthecuttingunitwith

thekickstandtoensurethatthenutsonthebackend

ofthebedbaradjustingscrewsarenotrestingonthe

worksurface(Figure36).

g003985

Figure36

1.Cutting-unitkickstand

Securethekickstandtothechainbracketwiththe

snapperpin(Figure37).

g004144

Figure37

ApplyingtheCEDecals

Partsneededforthisprocedure:

CEdecal

1Productionyeardecal

1Warningdecal

ApplyingtheCEDecal

1.Userubbingalcoholandacleanragtoclean

theareaofthehoodnexttothehoodlock,and

allowthehoodtodry.(Figure38).

Main Page

Table of Contents3
Safety4
General Safety4
Safety and Instructional Decals5
Setup10
Preparing the Machine10
Adjusting the Control-Arm Position11
Installing the Cutting Units11
Installing Rear Weights20
Installing the CE Hood Lock21
Using the Cutting-Unit Kickstand22
Applying the CE Decals22
Product Overview24
Controls24
Specifications30
Attachments/Accessories30
Before Operation30
Before Operation Safety30
Fuel Specification31
Fuel Tank Capacity31
Adding Fuel31
Performing Daily Maintenance31
Checking the Interlock Switches31
During Operation32
Breaking in the Machine32
Starting the Engine32
Shutting off the Engine32
Setting the Reel Speed33
Adjusting the Lift-Arm Counterbalance33
Adjusting the Lift-Arm Turnaround Position33
Adjusting the Turf-Compensation Spring34
Understanding the Diagnostic Light34
Operating Tips35
After Operation35
After Operation Safety35
Hauling the Machine35
Identifying the Tie-Down Points35
Pushing or Towing the Machine36
Maintenance37
Maintenance Safety37
Recommended Maintenance Schedule(S)37
Daily Maintenance Checklist39
Pre-Maintenance Procedures40
Preparing for Maintenance40
Opening the Hood40
Closing the Hood40
Opening the Screen40
Closing the Screen40
Tilting the Seat41
Lowering the Seat41
Jacking Point Locations41
Lubrication42
Greasing the Bearings and Bushings42
Engine Maintenance44
Engine Safety44
Servicing the Air Cleaner44
Checking the Engine-Oil Level44
Servicing the Engine Oil and Filter45
Fuel System Maintenance46
Draining the Fuel-Water Separator47
Bleeding the Fuel System47
Checking the Fuel Lines and Connections47
Changing the Fuel-Water Separator Filter48
Draining and Cleaning the Fuel Tank48
Cleaning the Fuel-Intake Screen48
Electrical System Maintenance49
Electrical System Safety49
Disconnecting the Battery49
Connecting the Battery50
Charging the Battery50
Servicing the Battery50
Replacing a Fuse-Block Fuse51
Replacing the Telematic Fuse51
Drive System Maintenance52
Checking the Tire Air Pressure52
Checking the Torque of the Wheel Nuts52
Adjusting the Traction Drive for Neutral52
Checking the Rear-Wheel Alignment53
Adjusting the Rear Wheel Toe-In53
Cooling System Maintenance54
Cooling System Safety54
Coolant Specification54
Checking the Coolant Level54
Removing Debris from the Cooling System55
Brake Maintenance56
Adjusting the Parking Brakes56
Adjusting the Parking-Brake Latch57
Belt Maintenance57
Servicing the Alternator Belt57
Hydraulic System Maintenance58
Hydraulic System Safety58
Hydraulic Fluid Specifications58
Checking the Hydraulic-Fluid Level58
Checking the Hydraulic Lines and Hoses59
Replacing the Hydraulic Filters59
Hydraulic Fluid Capacity60
Changing the Hydraulic Fluid60
Cutting Unit System Maintenance61
Blade Safety61
Checking the Reel-To-Bedknife Contact61
Backlapping the Cutting Units61
Chassis Maintenance63
Inspecting the Seat Belt63
Extended Maintenance64
Chassis and Engine64
Cleaning64
Washing the Machine64
Storage65

Toro 03678 - Using the Cutting-Unit Kickstand; Applying the CE Decals

Table of Contents

Other manuals for Toro 03678

Related product manuals