To Next Page
J
Jose YoungSep 9, 2025
Why doesn't my Toro Tiller drive?
- SsarablackSep 9, 2025
If your Toro Tiller does not drive, check the transmission belt. If it is worn, loose, or broken, change the belt. Also, change the belt if it is off a pulley.
Why doesn't my Toro Tiller drive?
If your Toro Tiller does not drive, check the transmission belt. If it is worn, loose, or broken, change the belt. Also, change the belt if it is off a pulley.
Why is there abnormal vibration in my Toro Tiller?
If you notice abnormal vibration in your Toro Tiller, inspect the tines for any bending and replace them if necessary. Tighten the tine mounting bolts and the engine mounting bolts. Also, tighten any loose engine pulleys or idler pulleys. Ensure that the jackshaft drive chain tension, the drive wheel chain tension, and the tine drive chain tension are properly adjusted and install a new belt if a belt is damaged.
What causes my Toro 29518 Tiller engine to overheat?
If your Toro Tiller engine overheats, first, reduce the ground speed or aeration depth. Then, check the oil level in the crankcase and add oil if needed. Finally, remove any obstructions from the cooling fins and air passages to ensure proper cooling.
Why won't my Toro 29518 Tiller engine start?
If your Toro Tiller's engine won't start, starts with difficulty, or stalls, several factors could be at play. Begin by ensuring the fuel tank is adequately filled and the fuel shutoff valve is open. For a cold engine, make sure the choke is in the On position; for a warm engine, ensure it's Off. Also, the throttle control should be midway between the Slow and Fast positions. Check and replace the fuel filter if it's dirty, and inspect the spark plug wire connection. Clean, adjust, or replace the spark plug if it's faulty. Clean or replace the air cleaner element if it is dirty. Finally, inspect electrical connections, clean the connector terminals, apply dielectric grease, and reconnect them to ensure good contact.
How to fix Toro 29518 tines that do not raise?
If the tines on your Toro Tiller aren't raising, it could be due to an auxiliary pump belt problem, so tension or replace the belt. Another potential cause is that the tine down pressure setting is too low, so increase the down pressure. Finally, add oil to the auxiliary reservoir if it is low.
Why does my Toro 29518 Tiller not drive?
If your Toro Tiller isn't driving, it could be due to a worn, loose, or broken drive belt or pump belt; in this case, change the belt. Another possibility is that the drive belt or pump belt has come off a pulley, in which case you should also change the belt.
What to do if Toro 29518 tines do not engage the ground?
If the tines on your Toro Tiller aren't engaging the ground, first increase the tine down pressure setting. Also, remove the cylinder stop, clevis pin, and hair pin. Finally, add oil to the auxiliary reservoir if it is low.
Why does my Toro 29518 pull to one side?
If your Toro Tiller pulls to the left or right even with the levers fully forward, start by checking and adjusting the tire pressure in the drive tires to ensure they are correct. If the issue persists, adjust the motion control linkage to correct the tracking.
What causes a Toro 29518 engine to overheat?
If your Toro Tiller engine is overheating, the engine load may be excessive; reduce the ground speed or aeration depth. Ensure that the oil level in the crankcase is adequate by adding oil if it's low. Also, check the cooling fins and air passages for the engine and remove any obstructions.
How to fix abnormal vibration in my Toro 29518 Tiller?
Abnormal vibration in your Toro Tiller can stem from several sources. Start by inspecting the tines for any bending and replace if necessary. Ensure the tine mounting bolts and engine mounting bolts are tightened securely. Check for any loose engine pulley or idler pulley and tighten the appropriate pulley. Inspect the belts for damage and replace if needed. Finally, check the jackshaft drive chain tension, the drive wheel chain tension, and the tine drive chain.
General
