Toro TimeCutter 75746 User Manual (English)

Questions and Answers:

C
Chad WardAug 7, 2025
Why is my Toro TimeCutter 75746 engine overheating?
- J
  Jacqueline HuntAug 7, 2025
  Several factors can cause your Toro Lawn Mower engine to overheat. First, the engine load might be excessive, so reduce the ground speed. Second, check the oil level in the crankcase and add oil if it is low. Third, obstructions in the cooling fins and air passages under the engine-blower housing can cause overheating; remove any obstructions. Fourth, a dirty air cleaner can contribute to the problem, so clean or replace the air-cleaner element. If the issue persists, there may be dirt, water, or stale fuel in the fuel system, in which case you should contact an Authorized Service Dealer.
J
Joshua LambertAug 11, 2025
How to fix uneven cutting height on my Toro Lawn Mower?
- R
  rhonda00Aug 11, 2025
  Uneven cutting height on your Toro Lawn Mower can result from several factors. Ensure the blade(s) is sharp; if not, sharpen them. Check for bent cutting blade(s) and replace them if necessary. Level the mower from side-to-side and front-to-rear. If applicable, adjust the anti-scalp wheel height. Clean the underside of the mower deck, and adjust the tire pressure. If a blade spindle is bent, contact an Authorized Service Dealer.
S
shaysAug 16, 2025
Why are the blades not rotating on my Toro TimeCutter 75746?
- M
  Michael GriffithAug 16, 2025
  If the blades on your Toro Lawn Mower aren't rotating, several issues could be the cause. A worn, loose, or broken drive belt can prevent blade rotation, so install a new drive belt. Additionally, ensure the drive belt is properly installed on the pulley, checking the adjusting shafts and belt guides for correct positioning. If the power-takeoff (PTO) switch or PTO clutch is faulty, or the mower belt is worn, loose, or broken, contact an Authorized Service Dealer or install a new mower belt.
S
Scott SanchezAug 20, 2025
Why does my Toro TimeCutter 75746 engine lose power?
- B
  brookegarrisonAug 20, 2025
  If your Toro Lawn Mower engine loses power, consider the following potential causes: * The engine load may be too high; reduce the ground speed. * A dirty air cleaner can restrict airflow; clean the air-cleaner element. * Low oil level in the crankcase can cause power loss; add oil. * Blocked cooling fins and air passages under the engine blower housing can lead to overheating and power loss; remove any obstructions. * Faulty spark plug(s) (pitted, fouled, or with an incorrect gap) can reduce engine power; install a new, correctly gapped spark plug(s). For issues such as a blocked fuel-tank vent, dirt in the fuel filter, dirt, water, or stale fuel in the fuel system, or incorrect fuel in the fuel tank, contact an Authorized Service Dealer.
A
akellerAug 25, 2025
What to do if my Toro TimeCutter 75746 Lawn Mower starter does not crank?
- R
  Ryan GonzalesAug 25, 2025
  If the starter on your Toro Lawn Mower doesn't crank, check these items: * Ensure the blade-control switch is disengaged. * Make sure the motion-control levers are in the PARK position. * Check the battery and charge it if it's dead. * Inspect the electrical connections for corrosion or looseness and ensure good contact. * See if a fuse is blown and replace it if necessary. If a relay or switch is damaged, contact an Authorized Service Dealer.
N
Natasha OlsonAug 29, 2025
Why is my Toro Lawn Mower vibrating abnormally?
- V
  Vanessa RussellAug 29, 2025
  Abnormal vibration in your Toro Lawn Mower can stem from several issues. Start by checking the cutting blades for bending or imbalance; if found, install new cutting blades. Then, ensure the blade mounting bolt and engine mounting bolts are tightened securely. Also, inspect the engine pulley, idler pulley, or blade pulley for looseness and tighten the appropriate pulley. For a damaged engine pulley, bent blade spindle, or loose/worn motor mount, contact an Authorized Service Dealer.

Toro TimeCutter 75746 Specifications

General

Brand	Toro
Model	TimeCutter 75746
Category	Lawn Mower
Language	English

Summary

Introduction

Safety

General Safety

Follow all safety instructions to avoid serious personal injury or death.

Slope Indicator and Safety

Guide to understanding slope indicators and safety for slopes.

Safety Decals and Warnings

Explanation of safety decals, symbols, and specific warnings.

Slope Safety

Guidelines and warnings for safe operation on slopes.

Product Overview

Controls

Control Panel Layout

Overview of the control panel with key switch, throttle, choke, and PTO.

Key Switch Operation

Details on the key switch positions: OFF, RUN, and START.

Throttle and Choke Controls

How to use throttle and choke for engine speed and starting.

Blade-Control Switch (PTO)

Engages and disengages power to the mower blades.

Motion-Control Levers and Park Position

Instructions for operating motion-control levers for driving and parking.

Smart Speed™™ Control System

Explanation of the 3-speed range system for controlling machine speed.

Fuel-Presence Window

How to check the fuel level using the window on the machine.

Operation

Before Operation

Procedures and safety checks to perform before starting the mower.

Height-of-Cut Adjustment

How to adjust the mower deck cutting height using the lever.

Attachments/Accessories

Information on Toro approved attachments and accessories.

Positioning the Seat

How to adjust the seat forward and backward for comfort and control.

Adjusting the Motion-Control Levers

How to adjust the motion-control levers higher or lower for comfort.

During Operation Safety

General safety guidelines for operating the mower safely.

Driving the Machine

Instructions for driving the machine forward and backward.

Fuel Safety

Adding Fuel

Recommended fuel types and procedures for safely adding fuel to the tank.

Filling the Fuel Tank

Step-by-step instructions for safely filling the fuel tank.

Maintenance

Maintenance Safety

Critical safety precautions to follow before and during maintenance.

Recommended Maintenance Schedule(s)

Table outlining maintenance tasks and service intervals.

Performing Daily Maintenance

Procedures to perform before starting the machine each day.

Pre-Maintenance Procedures

Raising the Machine

Safe procedures for raising the machine for maintenance.

Lubrication

Greasing the Bearings

Procedure for greasing caster wheel bearings at specified intervals.

Engine Maintenance

Engine Safety

Safety precautions related to engine components and operation.

Servicing the Air Cleaner

Instructions for cleaning and replacing air cleaner elements.

Servicing the Engine Oil

Engine-Oil Specifications

Details on oil type, capacity, and viscosity for the engine.

Checking the Engine-Oil Level

Procedure for checking the engine oil level before each use.

Changing the Engine Oil and Oil Filter

Procedure for changing engine oil and oil filter at specified intervals.

Servicing the Spark Plug

Checking the Spark Plug

How to check the spark plug condition and set the air gap.

Installing the Spark Plug

Procedure for installing the spark plug correctly.

Cleaning the Blower Housing

Fuel System Maintenance

Replacing the In-Line Fuel Filter

Procedure for replacing the in-line fuel filter at specified intervals.

Electrical System Maintenance

Electrical System Safety

Safety precautions for working with the electrical system.

Servicing the Battery

Procedure for removing the battery for servicing.

Charging the Battery

Instructions for charging the battery before storage or use.

Installing the Battery

Procedure for reinstalling the battery after servicing.

Servicing the Fuses

Drive System Maintenance

Checking the Tire Pressure

How to check and maintain proper tire pressure for even cutting.

Releasing the Electric Brake

Procedure for manually releasing the electric brake.

Adjusting the Tracking

How to adjust the machine's tracking for straight forward motion.

Belt Maintenance

Inspecting the Belts

How to inspect belts for wear or cracks.

Replacing the Mower Belt

Procedure for replacing the mower belt.

Mower Maintenance

Blade Safety

Safety precautions when inspecting, servicing, or replacing mower blades.

Servicing the Cutting Blades

Procedure for sharpening and maintaining mower blades.

Checking for Bent Blades

How to check if mower blades are bent.

Removing the Blades

Procedure for safely removing mower blades.

Installing the Blades

Procedure for correctly installing mower blades.

Leveling the Mower Deck

Procedure for ensuring the mower deck is level.

Checking the Side-to-Side Level

Procedure to check and adjust the side-to-side deck level.

Checking the Front-to-Rear Blade Slope

Procedure to check front-to-rear blade slope.

Leveling from Side to Side

Detailed procedure for leveling the mower deck side-to-side.

Adjusting the Front-to-Rear Blade Slope

Procedure to adjust the front-to-rear mower deck slope.

Removing the Mower Deck

Procedure for safely removing the mower deck from the machine.

Installing the Mower Deck

Procedure for safely installing the mower deck onto the machine.

Replacing the Grass Deflector

Procedure for replacing the grass deflector.

Cleaning

Washing the Underside of the Mower Deck

Procedure for cleaning the underside of the mower deck.

Disposing of Waste

Proper disposal methods for engine oil, batteries, and fluids.

Storage

Storage Safety

Safety precautions for storing the machine.

Cleaning and Storage

Steps for cleaning and preparing the machine for long-term storage.

Storing the Battery

Proper procedures and tips for storing the battery.

Troubleshooting

Engine Problems

Troubleshooting common engine issues like overheating or not starting.

Starting Problems

Troubleshooting when the starter does not crank or engine fails to start.

Engine Power Loss

Troubleshooting when the engine loses power.

Drive System Issues

Troubleshooting problems like machine not driving or vibrating.

Cutting Height Issues

Troubleshooting uneven cutting height.

Blade Rotation Issues

Troubleshooting when the mower blades do not rotate.

Schematics

Electrical Diagram

Provides the electrical wiring diagram for the machine.

California Proposition 65 Warning Information

Related product manuals

Toro TimeCutter 75748

56 pages

Toro TimeCutter 75742

56 pages

Toro TIMECUTTER 75740

215 pages

Toro TIMECUTTER 75745TA

215 pages

Toro TimeCutter MyRIDE 75747

56 pages

Toro TimeCutter 75734

60 pages

Toro TIMECUTTER 75755TA

215 pages

Toro TimeCutter 75730TA

60 pages

Toro TimeCutter MyRIDE 75756

56 pages

Toro TimeCutter MyRIDE 75761TA

56 pages

Toro TIMECUTTER HD 75201

153 pages

Toro TIMECUTTER HD 75202

153 pages

Toro TimeCutter 75746 User Manual

Table of Contents

Questions and Answers:

Toro TimeCutter 75746 Specifications

Summary

Introduction

Safety

General Safety

Slope Indicator and Safety

Safety Decals and Warnings

Slope Safety

Product Overview

Controls

Control Panel Layout

Key Switch Operation

Throttle and Choke Controls

Blade-Control Switch (PTO)

Motion-Control Levers and Park Position

Smart Speed™™ Control System

Fuel-Presence Window

Operation

Before Operation

Height-of-Cut Adjustment

Attachments/Accessories

Positioning the Seat

Adjusting the Motion-Control Levers

During Operation Safety

Driving the Machine

Fuel Safety

Adding Fuel

Filling the Fuel Tank

Maintenance

Maintenance Safety

Recommended Maintenance Schedule(s)

Performing Daily Maintenance

Pre-Maintenance Procedures

Raising the Machine

Lubrication

Greasing the Bearings

Engine Maintenance

Engine Safety

Servicing the Air Cleaner

Servicing the Engine Oil

Engine-Oil Specifications

Checking the Engine-Oil Level

Changing the Engine Oil and Oil Filter

Servicing the Spark Plug

Checking the Spark Plug

Installing the Spark Plug

Cleaning the Blower Housing

Fuel System Maintenance

Replacing the In-Line Fuel Filter

Electrical System Maintenance

Electrical System Safety

Servicing the Battery

Charging the Battery

Installing the Battery

Servicing the Fuses

Drive System Maintenance

Checking the Tire Pressure

Releasing the Electric Brake

Adjusting the Tracking

Belt Maintenance

Inspecting the Belts

Replacing the Mower Belt

Mower Maintenance

Blade Safety

Servicing the Cutting Blades

Checking for Bent Blades

Removing the Blades

Installing the Blades

Leveling the Mower Deck

Checking the Side-to-Side Level

Checking the Front-to-Rear Blade Slope

Leveling from Side to Side

Adjusting the Front-to-Rear Blade Slope

Removing the Mower Deck

Installing the Mower Deck

Replacing the Grass Deflector

Cleaning