– 5 –
9-EN 10-EN
3 Wired remote control
This remote control can control the operation of up to 8 indoor units.
The remote control has two sections: The display section and the operation section.
■ Display section
In the display below all the icons are shown. When the unit is in operation,
only relevant icons will be displayed.
• When the circuit breaker is turned on the fi rst time, fl ashes on the
display part of the remote control.
• While this display is fl ashing, the model is being automatically confi rmed.
Wait till display has disappeared to use the remote control.
NOTE
The LCD (Liquid Crystal Display) may temporarily be blurred due to static electricity.
1 SETTING display
Displayed during setup of the timer or other
settings.
2 Operation mode
The selected operation mode is displayed.
3 Check display
Displayed while the protective device works or a
problem occurs.
4 Timer display
Indicates time concerning the timer.
(Indicates a check code when a problem occurs)
5 Timer Mode display
Displays the timer mode.
6 Filter display
, reminder to clean the air filter.
7 TEST run display
Displayed during a test run.
8 Louver position display
Displays louver position.
* Only for 4-way cassette type, Compact 4-way
cassette type, Ceiling type, High wall type.
9 Swing display
Displayed during up/down movement of the
louver.
10 Set temperature display
The selected set temp. is displayed.
11 Remote control sensor display
Displayed while the sensor of the remote control
is used.
SET
TIME
TIMER SET
TEST
FILTER
RESET
TEMP.
CL
FAN
SAVE
SWING/FIX
VENT
MODE
ON / OFF
UNIT LOUVER
Display
section
Operation
section
Partition line
2
14
20
5
7
3
1
4
6
11
9
8
13
12
10
18
16
19
15
17
21
22
23
12 Pre-heat display
Displayed when the heating mode is energized or
defrost cycle is initiated.
While this indication is displayed, the indoor fan
stops.
13 No function display
Displayed when the function requested is not
available on that model.
14 Fan speed display
The selected fan speed mode is displayed.
(AUTO)
(HIGH)
(MED.)
(LOW)
Only “HIGH” is displayed for the high static
ducted type.
15 Louver Number display.
Louvers can be controlled individually. Displays
which louver is being set.
(example:01, 02, 03, 04)
(4-way cassette only)
16 Power saving mode display
Displayed when power saving mode is activated.
17 Louver lock display
Displayed when louver is locked or there is a
louver-locked unit in the group.
(4-way cassette type only)
18 UNIT No. display
Displays the number of the indoor unit selected.
Also displays check code of indoor and outdoor
units
19 SET DATA
Displayed during advanced setting.
20 Service display
Displayed while the protective device works or a
trouble occurs.
21 Function unavailable display
Displayed when the requested function is
currently unavailable.
22 Central control indicator
Displayed when the air conditioner is controlled
centrally and used with central control devices
such as the central remote control.
If the use of the remote control is prohibited by
the central control,
blinks when the ON/OFF,
MODE, or TEMP. button on the remote control is
pushed, and the buttons do not function.
(Settings that can be configured on the remote
control differ depending on the mode of the
central control. For details, read the Owner’s
Manual of the central remote control.)
23 Operation mode controlled indicator
Displayed when MODE button is pushed while
operation mode is fixed to cool or heat by the air
conditioner administrator.
2
5
7
3
1
4
6
11
9
8
10
14
20
13
12
18
16
19
15
17
21
22
23
1117907101 EN FR.indb 51117907101 EN FR.indb 5 3/21/16 11:44 AM3/21/16 11:44 AM
To Next Page
Loading...
