Toshiba RAS-B10J2KVSG-E - Preparation Before Use; Preparing Filters; Loading Batteries; Clock Setup

1
-
2
3
4
6
5
(
%
&
"
7
!
9
<
8
#
)
$
/
,
~
+
:
;
.
Preparing Filters
1. Open the air inlet grille and remove the air lters.
2. Attach the lters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push
by tip of the pencil.
If timer indication is ashing, go to the next step 2.
2. Press
or : adjust the time.
3. Press
: Set the time.
Remote Control Reset
Push
by tip of the pencil or
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
AIR FLOW DIRECTION
3
Note:
● The provided Remote Controller is a wireless type, which also can be
used as a wire. Please see “How to Connect The Remote Controller
for Wired Operation”, located in installation instruction, in case of wired
control is required.
● In wire operation, remote controller will return to initial condition
(PRESET, TIMER and CLOCK will return to initial condition) when user
shutdown power supply of Air conditioner.
REMOTE CONTROL
4
1
Infrared signal emitter
2
Memory and Preset button (PRESET)
3
Start/Stop button
4
Mode select button (MODE)
5
Air ow button
6
Fireplace/8°C button
7
ECO button
8
Comfort sleep button (COMFORT SLEEP)
9
Weekly timer (ON/OFF)
!
Temp for Weekly timer
"
On timer button (ON)
#
Set clock button (CLOCK)
$
Check button (CHECK)
%
Filter reset button (FILTER)
&
Temperature button (TEMP)
(
Swing louver button (SWING)
)
Fan speed button (FAN)
~
Set louver button (FIX)
+
High power button (Hi-POWER)
,
Power selection/Silent button (P-SEL/SILENT)
-
Program P1 - P4
.
Day/Edit button
/
Setup button (SET)
:
Off timer button (OFF)
;
Clear button (CLR)
<
Reset button (RESET)
AUTOMATIC OPERATION
6
To automatically select cooling, heating or fan only operation
1. Press
MODE
: Select Auto A.
2. Press
: Set the desired temperature. Min. 17°C, Max. 30°C
3. Press
FAN
: Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or QUIET
DRY OPERATION
7
For dehumidication, a moderate cooling performance is controlled
automatically.
1. Press
MODE
: Select Dry .
2. Press
: Set the desired temperature. Min. 17°C, Max. 30°C
Note : DRY mode fan speed is set to Auto only.
Hi-POWER OPERATION
8
To automatically control room temperature and airow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press
Hi POWER
: Start and stop the operation.
ECO OPERATION
9
To automatically control room temperature to save energy (except in DRY
and FAN ONLY mode)
Press
: Start and stop the operation.
Note : Cooling operation; the set temperture will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase).
For heating operation the set temperture will decrease.
PREPARATION BEFORE USE
2
1
Press
FIX
: Move the louver in
the desired vertical direction.
2
Press
SWING
: Swing the air
automatically and press again to stop.
3
For horizontal direction, adjust
manually.
Note:
● Do not move the louver manually by others.
● The louver may automation positioning by some operation mode.
1. Press
MODE
: Select Cool , Heat or Fan only .
2.
Press : Set the desired temperature. Min. 17°C, Max. 30°C,
Fan Only: No temperature indication
3. Press
FAN
: Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or QUIET
COOLING / HEATING / FAN ONLY OPERATION
5
INDOOR UNIT DISPLAY
1
● Display brightness can be adjusted, follow procedure on (.
w Require Wireless LAN connecting adapter which available as accessory.
1
ECO (White)
2
Wi-Fi access (White) w
3
Hi-Power (White)
4
Timer (White)
5
Operation mode
- Cool (Blue)
- Heat (Orange)
Fireplace Operation ( )
Keep indoor unit’s fan blowing continuously during thermo off, to circulate heat
from other sources over the room. There are three setting parameters: Default
setting > Fireplace 1 > Fireplace 2
Fireplace 1:
During thermo off period, the indoor unit’s fan will continue to run by the same
speed, previously selected by end-user.
Fireplace 2:
During thermo off period, the indoor unit’s fan will continue to run at super-low
speed, programmed from factory.
8°C Heating Operation (8°C)
Heat mode operation for keep room temperature (5-13°C) with less of energy
usage.
Fireplace and 8°C Heating Operation
8°C
FIREPLACE 1 FIREPLACE 2
Normal
operation
Note:
● While Fireplace operation on heating mode, indoor unit fan always runs
and cold air breezing might be occurred.
● Fireplace and 8°C will operate in Heating mode only.
FIREPLACE AND 8°C HEATING OPERATION
10